Contact Us
Solve Your Materials Challenges
Find out how we can help
The creation of the EEC (European Economic Community) has made it necessary to establish common standards named "European Norms" (EN), therefore standardizing the common language across Europe. Since 1988 a new series of 'mandatory' European standards (EN) has been created, to replace national standards, such as BS, DIN, SS and NF, throughout 18 countries of Western Europe.
The European (EN) standards include of specifications for delivery conditions, properties, quality, dimensions and definitions of all products, raw materials and processes of the iron and steel industry. Among others, Euronorm standards cover a large variety of structural and constructional steels, from hot and cold rolled steels, plates, sheets and strips, heat treatable steels, castings, stainless and heat resisting steels, electrical steels etc.
For more information on the EN designation system see Introduction to the Euronorm Standard Designation System.
The table below provides a part of the most important Euronorm standards for structural and constructional steels.
For further examples of Structural and Constructional Steel Standards see Euronorm Structural and Constructional Steels: Part Two.
The list of standards below cover among other things:
| Standard Number |
Last version |
Description | Status |
| EN 10016-1 | 1994 | Non-alloy steel rod for drawing and/or cold rolling - Part 1: General requirements | |
| EN 10016-2 | 1995 | Non-alloy steel rod for drawing and/or cold rolling - Part 2: Specific requirements for general purposes rod | |
| EN 10016-3 | 1995 | Non-alloy steel rod for drawing and/or cold rolling - Part 3: Specific requirements for rimmed and rimmed substitute low carbon steel rod | |
| EN 10016-4 | 1995 | Non-alloy steel rod for drawing and/or cold rolling - Part 4: Specific requirements for rod for special applications | |
| EN 10017 | 2004 | Steel rod for drawing and/or cold rolling - Dimensions and tolerances | |
| EN 10020 | 2000 | Definition and classification of grades of steel | |
| EN 10021 | 2006 | General technical delivery conditions for steel products | |
| EN 10024 | 1995 | Hot rolled taper flange I sections - Tolerances on shape and dimensions | |
| EN 10025 | 1993 | Hot rolled products of non-alloy structural steels; technical delivery conditions | Replaced by EN 10025-1/2004; 10025-2/2004 |
| EN 10025-1 | 2004 | Hot rolled products of structural steels - Part 1: General technical delivery conditions | |
| EN 10025-2 | 2004 | Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels | |
| EN 10025-3 | 2004 | Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels | |
| EN 10025-4 | 2004 | Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels | |
| EN 10025-5 | 2004 | Hot rolled products of structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance | |
| EN 10025-6 | 2004 | Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition | |
| EN 10028-1 | 2007 | Flat products made of steels for pressure purposes - Part 1: General requirements | |
| EN 10028-2 | 2009 | Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties | |
| EN 10028-3 | 2009 | Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized | |
| EN 10028-4 | 2009 | Flat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties | |
| EN 10028-5 | 2009 | Flat products made of steels for pressure purposes - Part 5: Weldable fine grain steels, thermomechanically rolled | |
| EN 10028-6 | 2009 | Flat products made of steels for pressure purposes - Part 6: Weldable fine grain steels, quenched and tempered | |
| EN 10028-7 | 2007 | Flat products made of steels for pressure purposes - Part 7: Stainless steels | |
| EN 10029 | 1991 | Hot rolled steel plates 3 mm thick or above - Tolerances on dimensions, shape and mass | |
| EN 10031 | 2003 | Semi-finished products for forging - Tolerances on dimensions shape and mass | |
| EN 10034 | 1993 | Structural steel I and H sections - Tolerances on shape and dimensions | |
| EN 10048 | 1996 | Hot rolled narrow steel strip - Tolerances on dimensions and shape | |
| EN 10051 | 1997 | Continuously hot-rolled uncoated plate, sheet and strip of non-alloy and alloy steels - Tolerances on dimensions and shape | |
| EN 10055 | 1995 | Hot rolled steel equal flange tees with radiused root and toes - Dimensions and tolerances on shape and dimensions | |
| EN 10056-1 | 1998 | Structural steel equal and unequal leg angles - Part 1: Dimensions | |
| EN 10056-2 | 1993 | Structural steel equal and unequal leg angles - Part 2: Tolerances on shape and dimensions | |
| EN 10058 | 2003 | Hot rolled flat steel bars for general purposes - Dimensions and tolerances on shape and dimensions | |
| EN 10059 | 2003 | Hot rolled square steel bars for general purposes - Dimensions and tolerances on shape and dimensions | |
| EN 10060 | 2003 | Hot rolled round steel bars for general purposes - Dimensions and tolerances on shape and dimensions | |
| EN 10061 | 2003 | Hot rolled hexagon steel bars for general purposes - Dimensions and tolerances on shape and dimensions | |
| EN 10067 | 1996 | Hot rolled bulb flats - Dimensions and tolerances on shape, dimensions and mass | |
| EN 10080 | 2005 | Steel for the reinforcement of concrete - Weldable reinforcing steel – General | |
| EN 10083-1 | 2006 | Steels for quenching and tempering - Part 1: General technical delivery conditions | |
| EN 10083-2 | 2006 | Steels for quenching and tempering - Part 2: Technical delivery conditions for non alloy steels | |
| EN 10083-3 | 2006 | Steels for quenching and tempering - Part 3: Technical delivery conditions for alloy steels | |
| EN 10084 | 2008 | Case hardening steels - Technical delivery conditions | |
| EN 10085 | 2001 | Nitriding steels - Technical delivery conditions | |
| EN 10087 | 1998 | Free-cutting steels - Technical delivery conditions for semi-finished products, hot-rolled bars and rods | |
| EN 10089 | 2002 | Hot-rolled steels for quenched and tempered springs - Technical delivery conditions | |
| EN 10090 | 1998 | Valve steels and alloys for internal combustion engines | |
| EN 10092-1 | 2003 | Hot rolled spring steel flat bars - Part 1: Flat bars - Dimensions and tolerances on shape and dimensions | |
| EN 10092-2 | 2003 | Hot rolled spring steel flat bars - Part 2: Ribbed and grooved spring leaves - Dimensions and tolerances on shape and dimensions | |
| EN 10108 | 2004 | Round steel rod for cold heading and cold extrusion - Dimensions and tolerances | |
| EN 10111 | 2008 | Continuously hot-rolled low carbon steel sheet and strip for cold forming - Technical delivery conditions | |
| EN 10113-2 | 1993 | Hot-rolled products in weldable fine grain structural steels - Part 2: delivery conditions for normalized rolled steels | Replaced by EN 10025-1:2004; EN 10025-3:2004 |
| EN 10113-3 | 1993 | Hot-rolled products in weldable fine grain structural steels - Part 3: delivery conditions for thermomechanically rolled steels | Replaced by EN 10025-1:2004; EN 10025-4:2004 |
| EN 10120 | 2008 | Steel sheet and strip for welded gas cylinders | |
| EN 10130 | 2006 | Cold rolled low carbon steel flat products for cold forming - Technical delivery conditions | |
| EN 10131 | 2006 | Cold rolled uncoated and zinc or zinc-nickel electrolytically coated low carbon and high yield strength steel flat products for cold forming - Tolerances on dimensions and shape | |
| EN 10132-1 | 2000 | Cold rolled narrow steel strip for heat treatment - Technical delivery conditions - Part 1: General | |
| EN 10132-2 | 2000 | Cold rolled narrow steel strip for heat treatment - Technical delivery conditions - Part 2: Case hardening steels | |
| EN 10132-3 | 2000 | Cold rolled narrow steel strip for heat treatment - Technical delivery conditions - Part 3: Steels for quenching and tempering | |
| EN 10132-4 | 2000 | Cold rolled narrow steel strip for heat treatment - Technical delivery conditions - Part 4: Spring steels and other applications | |
| EN 10137-2 | 1995 | Plates and wide flats made of high yield strength structural steels in the quenched and tempered or precipitation hardened conditions - Part 2: Delivery conditions for quenched and tempered steels | Replaced by EN 10025-1:2004; EN 10025-6:2004 |
| EN 10137-3 | 1995 | Plates and wide flats made of high yield strength structural steels in the quenched and tempered or precipitation hardened conditions - Part 3: Delivery conditions for precipitation hardened steels | Withdrawn 2000 |
| EN 10139 | 1997 | Cold rolled uncoated mild steel narrow strip for cold forming - Technical delivery conditions | |
| EN 10140 | 2006 | Cold rolled narrow steel strip - Tolerances on dimensions and shape | |
| EN 10149-1 | 1995 | Hot-rolled flat products made of high yield strength steels for cold forming - Part 1: General delivery conditions | |
| EN 10149-2 | 1995 | Hot-rolled flat products made of high yield strength steels for cold forming - Part 2: Delivery conditions for thermomechanically rolled steels | |
| EN 10149-3 | 1995 | Hot-rolled flat products made of high yield strength steels for cold forming - Part 3: Delivery conditions for normalized or normalized rolled steels | |
| EN 10155 | 1993 | Structural steels with improved atmospheric corrosion resistance - Technical delivery conditions | Replaced by EN 10025-5:2004 |
| EN 10162 | 2003 | Cold rolled steel sections - Technical delivery conditions - Dimensional and cross-sectional tolerances | |
| EN 10163-1 | 2004 | Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 1: General requirements | |
| EN 10163-2 | 2004 | Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 2: Plate and wide flats | |
| EN 10163-3 | 2004 | Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 3: Sections | |
| EN 10164 | 2004 | Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions | |
| EN 10168 | 2004 | Steel products - Inspection documents - List of information and description | |
| EN 10207 | 2005 | Steels for simple pressure vessels - Technical delivery requirements for plates, strips and bars | |
| EN 10208-1 | 2009 | Steel pipes for pipelines for combustible fluids - Technical delivery conditions - Part 1: Pipes of requirement class A | |
| EN 10208-2 | 2009 | Steel pipes for pipelines for combustible fluids - Technical delivery conditions - Part 2: Pipes of requirement class B | |
| EN 10209 | 1996 | Cold rolled low carbon steel flat products for vitreous enamelling - Technical delivery conditions | |
| EN 10210-1 | 2006 | Hot finished structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions | |
| EN 10210-2 | 2006 | Hot finished structural hollow sections of non-alloy and fine grain steels - Part 2: Tolerances, dimensions and sectional properties |
Total Materia is the leading materials information platform, providing the most extensive information on metallic and non-metallic material properties and other material records.
All this information is available in Total Materia Horizon, the ultimate materials information and selection tool, providing unparalleled access to over 540,000 materials as well as, curated and updated reference data.
Total Materia Horizon includes: