Plasma Nitriding of Steels: Part One


Plasma nitriding improves the wear resistance of a material by effectively altering the surface microstructure while maintaining adequate substrate properties.
Nitriding occurs when a bias voltage is applied to the work piece causing ions to collide with the surface and consequently creating the nitride effect.

Nitriding is a thermochemical surface treatment used in steels and alloys to improve wear and friction properties by surface microstructure modification, while maintaining adequate substrate properties. Not only wear resistance is improved, but also corrosion and fatigue resistance may be increased by the same treatment. Plasma nitriding is the most versatile nitriding process and has many advantages over conventional salt-bath and gas nitriding. The close control of the metallurgical properties of the nitrided surface is the most important advantage of the plasma nitriding process. Nowadays duplex and hybrid layers are growing in importance, requiring prior plasma nitriding of the substrate to avoid compound layer formation.

Plasma nitriding or ion nitriding is a modern process used to impart surface hardening to metals for a wide variety of applications. As the name implies, the process is carried out in a plasma media containing ionized nitrogen alone, or in combination with other gasses to react with the work surface. The process was independently patented by Egan (1931), and Berghaus (1932, 1939), and advances in the field of power electronics have caused the process to gain World-wide popularity in a variety of applications.

One outstanding advantage of plasma heat treatment is the lower environmental impact it poses compared with heat treatment with a controlled atmosphere furnace. For example, nitriding with a controlled atmosphere furnace often uses ammonia gas. In contrast, using a plasma nitriding technique, a steel material can be nitrided with nitrogen and hydrogen. Also, with plasma nitriding, the intended work-piece alone is heated without heating the entire interior of the furnace—a practice necessary for a controlled atmosphere furnace.

Figure 1 shows schematics of typical plasma heat treatment equipment configurations. With cold-wall or hot-wall configurations where a bias voltage is applied to a work-piece, a clean surface is exposed on the work-piece through sputtering where ions collide with the work-piece. Consequently, the surface of a material is nitrided in a short time even if the material type needs a longer time for nitriding with a gas nitriding or vacuum nitriding process.

Figure 1: Schematic diagram of plasma heat treating equipment

The advantages of plasma nitriding can be summarized as follows:
1. Plasma nitriding is essentially faster than other conventional nitriding techniques.
2. Proper control of the temperature, atmosphere composition, and discharge parameters can lead to production of superior microstructure and permit better control over the composition of the final product surface, its structure, and its properties.
3. Plasma nitriding is environmentally non polluting.
4. Unlike conventional nitriding treatments the process can operate at a temperature as low as 350°C. Low temperature nitriding allows high surface hardness to be achieved along with the maintenance of high core strength in low temperature tempering steels. Furthermore, treating at these low temperatures keeps distortion to a minimum.

There are a few disadvantages of the plasma nitriding process:

  • Cleanlinnes of surface of the components is essential to hinder unstable arc discharges forming during the heating cycle.
  • The need to fixture parts to avoid overheating.
  • Because of power/surface area relationships. Components with similar size may not be plasma nitrited in one batch.
  • The high initial plasma cost.


1. C.E.Pinedo: W.A.Monteiro: Surface hardening by plasma nitriding on high chromium alloy steel, Journal of Materials Science Letters 20, 2001, p.147-149

2. F.Mahboubi: The influence of the mode of plasma generation on the plasma nitriding behavior of a micoralloyed (i.e. microalloyed) steel, PhD thesis, University of Wollongong, Wollongong, Australia 1998

3. K.Yagita, C.Ohki: Plasma nitriding treatment of high alloy steel for bearing components, NTN Technical Review No 78, 2010, p.33-40

Criteri di ricerca
Inserite il vostro testo in inglese per la ricerca:

Ricerca tramite

Ricerca tramite

Testo completo


Diagrammi di Trattamento Termico sono disponibili per un notevole numero di materiali nel database Total Materia.

i diagrammi di Trattamento Termico coprono Temprabilità, Tempera/Durezza, TTT e CCT in accordo alle Normative di riferimento.

Per selezionare i materiali in base a proprietà speciali (es. Trattamento termico), è possibile utilizzare le caselle di controllo speciali di ricerca nel modulo di Ricerca Avanzata.

Per definire i criteri di ricerca, tutto ciò che si deve fare è selezionare il Paese e la Normativa di interesse dalla finestra a discesa Paese/Normativa e spuntare la casella di controllo 'Diagramma di Trattamento Termico', situato nella parte inferiore della pagina Ricerca Avanzata.

Fare clic su Invio.

Dopo aver selezionato la lega che interessa, si deve cliccare sul link "Trattamento Termico" per visualizzare i dati per il materiale selezionato. Il numero di records di Trattamento Termico viene visualizzato tra parentesi accanto al link.

Tutte le informazioni disponibili di Trattamenti Termici verranno visualizzate per il materiale scelto.

Per consentirvi di testare il Database Total Materia "senza impegno", vi invitiamo a unirvi alla comunità degli Utenti registrati per i test gratuiti a Total Materia.