The Continuous Rheoconversion Process

Abstract:

The Continuous Rheoconversion Process (CRP) is designed to be flexible allowing both thixocasting and rheocasting to be achieved by mixing two melts together at near liquidus temperatures to achieve smaller grain sizes and more globular structures.
Key advantages of the CRP include continuous conversion of liquid to slurry, can be used with different alloys, benefits in simplified re-cycling.

The Continuous Rheoconversion Process (CRP) is a novel, low-cost rheocasting process that was developed at MPI/WPI in 2002.

The process combined two separate techniques, liquid mixing and passive stirring, previously reported in the literature to produce globular slurries. The mixing of two melts of different composition (whether grain refined or not) near their respective liquidus temperatures and passive stirring of liquid metal in channels (instead of active stirring via mechanical or electromagnetic means) have been shown to promote smaller grain sizes and more globular structures.

It was thought that combining these two approaches would allow fully globular microstructures to be attained. Additionally, the CRP was designed to be flexible, allowing for thixocasting or rheocasting applications as well as batch or continuous casting.

The schematic diagram, Figure 1 illustrates the concept of a “tortuous path” to induce forced convection.



Figure 1: Schematic of the Continuous Rheoconversion Process (CRP)

The major characteristics of the CRP apparatus include independent temperature control of each precursor alloy melt, a heated channel system to transport the melts without any heat loss, and a reactor to (a) provide copious nucleation and (b) induce forced convection in the melts as they flow through it. The reactor can be preheated to vary its level of heat extraction. The above diagram is intended to provide the reader with the basic variables inherent to the device.

These parameters include but are not limited to independent control over the heat content of the melts, the chemical composition of each melt, and the rate at which heat is extracted from the “product melt” within the reactor.

Recently the CRP has been scaled up for industrial applications. To retrofit most die casting facilities, the reactor has been optimized and simplified in such a way that only one melt is involved wherein both nucleation and mixing takes place simultaneously within the reactor. Moreover, to enhance the control of melt nucleation and to conveniently adjust slurry fraction solid, an optimized cooling system is incorporated into the reactor (as illustrated in Figure 2).



Figure 2: CRP concept implemented within a typical die casting setting

The advantages of the CRP process include:

  • Continuous conversion of liquid to slurry
  • Flexible
  • Thixocasting or slurry-ready
  • Not alloy specific
  • Allows for rapid adjustment of solid content
  • Recycling of scrap easy to incorporate
  • Can be used with one melt as well - design flexibility
  • The CRP can accommodate significantly higher levels of superheat than existing slurry-on-demand processes
  • Commercially viable - patent application submitted and in process


References

1. Q. Pan, S. Wiesner, D. Apelian: Application of the Continuous Rheoconversion Process (CRP) to Low Temperature HPDC-Part I: Microstructure, Solid State Phenomena Vols. 116-117, 2006, p. 402-405, Trans Tech Publications, Switzerland, doi:10.4028/www.scientific.net/SSP.116-117.402

2. W.J.Bernard: The Continuius Rheoconversion Process: Scale-up and Optimization, Worcester Polytechnic Institute, MSc thesis, May 2005,

3. M. Findon, D. Apelian: The Continuous Rheoconversion Process for Semi-Solid Slurry Production, Copyright 2004 American Foundry Society, Final Technical Report, 2012, Accessed Nov 2016

4. Q. Pan, D. Apelian: Slurry-Ready SSM: The Continuous Rheoconversion Process (CRP), Accessed Dec 2016

Search Knowledge Base

Enter a phrase to search for:

Search by

Full text
Keywords

Headings
Abstracts

Heat treatment diagrams are available for a huge number of materials in the Total Materia database.

Heat treatment diagrams covering hardenability, hardness tempering, TTT and CCT can all be found in the standard dataset.

To select materials by special properties, you can use the special search check boxes in the Advanced Search module.

To define the search criteria, all you have to do is select the country/standard of interest to you from the ‘Country/Standard’ pop-up list and to check ‘Heat Treatment Diagram’ box, situated in the Special Search area of the form in the lower part of the Advanced Search page.

Click Submit.

solution img

After selecting the material of interest to you, click on the Heat Treatment link to view data for the selected material. The number of heat treatment records is displayed in brackets next to the link.

solution img

All available heat treatment information will then be displayed for the chosen material.

solution img

solution img

solution img

For you’re a chance to take a test drive of the Total Materia database, we invite you to join a community of over 150,000 registered users through the Total Materia Free Demo.