Phosphor Bronzes

요약:

Phosphor bronzes are alloys consisting of tin, phosphorus and copper as main constituents, sometimes with additions of zinc and lead. The structure is made up of three phases:

  • A matrix of copper with tin in solid solution, known as the alpha phase, which is comparatively soft
  • A tin rich delta phase which is hard and interspersed throughout the matrix
  • A hard constituent of copper phosphide associated with the delta constituent, which is also hard but brittle.

Phosphor bronzes are alloys consisting of tin, phosphorus and copper as main constituents, sometimes with additions of zinc and lead. The structure is made up of three phases:

  • A matrix of copper with tin in solid solution, known as the alpha phase, which is comparatively soft
  • A tin rich delta phase which is hard and interspersed throughout the matrix
  • A hard constituent of copper phosphide associated with the delta constituent, which is also hard but brittle.
The duplex structure of the alloy is ideal for bearing purposes. The toughness and hardness of the alloy can be varied with the tin and phosphorus content. In general, increases of tin give added toughness as well as hardness; increases in phosphorus give added hardness, but a tendency to brittleness. To avoid this brittleness care must be taken to limit the amount of phosphorus in the alloy to a maximum of 1-5%.

The phosphor bronzes can be sand cast, chill cast, continuously cast and centrifugally cast; they are largely used in the chill cast form, in which, owing to the quick cooling, the amounts of the hard constituents are increased and much more finely dispersed throughout the matrix than in the sand cast state giving an extremely tough and hard wearing alloy.

The grain structure of the chill cast and continuously cast alloy is not only finer than the sand cast alloy, but usually freer from porosity. The centrifugally cast alloy is usually sounder even than the chill cast alloy, equal in strength to it and higher in ductility.

The phosphor bronzes can be recommended for all services where toughness, wear resistance and hardness are required; they have good corrosion resistance to tap waters, mine waters, mild alkalis and petroleum derivatives. As their thermal and electrical conductivities are only a little inferior to the gunmetals, they are often useful when such properties are required because of their high mechanical strength.

The above properties make the phosphor bronzes very suitable for the following uses:

  • Bearings and bushes subject to varying loads and duties, gear and worm wheels
  • Parts for air compressors, aero engines, diesel engines
  • Marine parts, generator and mining machinery, hoist fittings, piston rings, chemical pressure vessels, zinc free pump bodies, casings and impellers, acid resisting castings.

PB1C (B.S.1059, STA7-CP5): Sn min. 10.0%; P min. 0.50%

This is a very high grade phosphor bronze, free from zinc, with low lead (0.25% max.) which was originally introduced for use in the mines and was later developed for the aircraft industry as B8 and subsequently 2B8.

It is used for gears, bearings and bushes for heavy loads and high duty with adequate lubrication, and for duty with hard steel shafts. Typical are bearings for aero engines, diesel engines, electrical generators and rolling mills. The alloy is also greatly used for gear and worm wheels, for pump parts particularly in mine waters and for marine work. The alloy can be chill cast, continuously cast, centrifugally cast and sand cast. For bearings and bushes a large amount is produced in the form of chill cast stick and continuously cast tubes and rods. For gears the alloy is mostly centrifugally, continuously or chill cast.

PB4C (SAE 65): Sn min. 9.5%; Pb max. 0.75%; Zn max. 0.5%; P min. 0.5%

For parts required for Air Ministry and Admiralty work of the highest quality, the alloy PB1 is necessary but where conditions are less onerous there is a place for an alloy of a similar type, but with a wider tolerance of impurities such as zinc, lead and nickel. To meet this need, the alloy PB4 has been introduced. The tin content is 0.5% lower than PB1 and lead is permitted up to 0.75% compared with 0.25% in PB1; zinc, which is absent from PB1, is permitted up to 0.5%.

PB2C (B.S.421, STA7-CP6, SAE 65): Sn=11.0-13.0%; Pb max. 0.50%; P min 0.15%

This alloy has a higher tin content than PB1 and lower phosphorus. It is tougher and therefore eminently suitable for gear and worm wheels which is its main use. It is resistant to shock and will stand heavy loading when used for bearing purposes. The alloy can be sand cast, chill cast, continuously cast and centrifugally cast.

PB3 (SAE65): Sn=8.0-11.0%; Pb max. 0.25%; P=0.10-0.40%

This alloy, which has a lower phosphorus content than PB1, is primarily intended for use as a zinc free copper-tin alloy for corrosion resistant and pressure tight castings. It has a very low impurity limit (0.30% excluding lead) and is used chiefly for chemical plant such as pressure vessels, pump bodies, casings and impellers.

LPB1C (B.S. 1061, STA7-CP3): Sn=6.5-8.5%; Pb=2.0-5.0%; P=min. 0.30%; Zn max. 2.0%; Ni max. 1.0%

This alloy has a lower tin and phosphorus content than PB1 and also contains up to 5% lead and may contain up to 2% of zinc and 1% of nickel. The lead is dispersed throughout the structure in fine globules. It is suitable for bearings and bushes for lighter duties, and due to the lead content, for use with limited lubrication. It is very easily machined.

The alloy can be sand cast, chill cast and centrifugally cast; large quantities are used in chill cast stick form for various types of bearings and bushes; it is also used for plant not required to stand the rigorous duties.

기술 자료 검색

검색할 어구를 입력하십시오:

검색 범위

본문
키워드

머릿글
요약

Total Materia는 다양한 나라와 규격에 따른 수천개의 구리 재질에 대한 정보를 포함하고 있습니다.

재질의 화학적 조성, 기계적 특성, 물리적 특성, 고급 물성 데이터 등의 전체적인 특성 정보들을 어디서든 검토하실 수 있습니다.

고급 검색을 이용하여, 검색 조건의 재질 리스트에서 '구리'를 선택합니다. 검색 범위 좀 더 줄이기를 원하신다면 국가/규격과 같은 다른 조건을 지정할 수 있습니다.

검색 버튼을 클릭합니다.


선택된 정보에 부합하는 일련의 재질이 검색됩니다.


결과 리스트에서 재질을 선택하시면, 일련의 규격 사양 소그룹이 나타납니다.

여기에서 선택한 재질의 특정 특성 데이터를 검토하실 수도 있고, 강력한 상호 참조 표를 이용하여 유사 재질이나 등가 재질을 검토하는 것 또한 가능합니다.


자세한 특성 데이터를 보시려면 특성 데이터 링크를 클릭하세요.

Total Materia 데이터베이스를 사용해 보실 수 있는 기회가 있습니다. 저희는 Total Materia 무료 체험을 통해 150,000명 이상의 사용자가 이용하고 있는 커뮤니티로 귀하를 초대합니다.