Overview of Spinodal Decomposition of Non-Ferrous Alloys: Part Two


Spinodal decomposition manifests itself as characteristic patterns in an alloy, which are a direct result of phase separation during the quenching process.
General spinodal decomposition properties and benefits include, to name but a few, excellent high temperature stress relaxation resistance, lack of distortion during aging, lower initial cost and cost savings during processing.

The addition of Ni between 4 and 15% and Sn between 4 and 8% to the Cu matrix constitutes spinodally decomposable Cu-Ni-Sn alloy system. The spinodally decomposable Cu-Ni-Sn Bronze alloys produce a modulated microstructure during the heat treatment process and its mechanical properties comparable to those of Cu-Be alloys, while being relatively inexpensive and hazard free. The modulated microstructure significantly increases the strength of the Cu-Ni-Sn alloys, and the increase is attributed to a) alloy composition (b) condition of the alloy cast or wrought) (c) amount of cold work prior to aging d) aging temperature and e) aging time. The Cu-Ni-Sn Bronze alloys can be used as the friction-reducing and anti-wear materials to make high performance bearings for aerospace, roller cone rock bit and heavy duty mobile industrial equipment etc.

It has been generally observed that five different transformation products exist in the Cu-Ni-Sn system as shown in Figure 1. They are: a) modulated structure resulting from spinodal decomposition b) DO22 ordered structure c) L12 ordered structure d) grain boundary and intra-granular γ DO3) precipitates and e) discontinuous γ precipitates. The above transformation is dependent on temperature and time Refer to Figure 2). At high temperature the grain boundary and intergranular γ DO3) precipitates form, whereas, in the middle range of temperature a discontinuous γ precipitates forms. Below the critical temperature TR ~457°C. the spinodal decomposition takes place. When the aging time is increased, an ordering reaction takes place forming DO22 and L12 ordered structure (Refer to Figure 2). The spinodal decomposition and ordering reaction increases the hardness and the YS of the alloys.

Figure 1: Spinodal decomposition process

Figure 2: A typical phase transformation diagram for the Cu-Ni-Sn Bronze alloy

Spinodal decomposition properties and benefits

  • Excellent high temperature stress relaxation resistance
  • High strength and excellent formability
  • Lack of distortion during aging
  • Available in mill hardened and age hardenable tempers
  • Excellent solderability and resistance to intermetallic formation at high temperature
  • Excellent corrosion resistance and ease of cleaning. In moist ammonia it resists corrosion for over 500 hrs. at 400°C
  • Lower initial cost and cost savings during processing

Limitations of spinodal decomposition
1. Limited alloying compositions are suitable for spinodal hardening.
2. It requires homogenization, solution treatment and aging treatment i.e. it is time consuming.
3. In ternary alloys metastable phase is of very short moment, so special care should be taken to achieve this region.
4. Micro examinations are needed in every stage of experiment.
5. Behavior of Spinodal decomposition may sometimes unpredictable.

1. Marine Environment
2. Automotive
3. Offshore oil and gas
4. Aerospace


1. Jirapure S.C, Borade A.B, Kongre U.V: A new approach of strengthening- spinodal decomposition, Int. Journal of Applied Sciences and Engineering Research, Vol. 4, Issue 1, 2015, ISSN 2277 – 9442;

2. Spinodal Copper, AMETEK Specialty Metal Products, Nickel strip, 2016, Accessed April 2019.

Criteri di ricerca
Inserite il vostro testo in inglese per la ricerca:

Ricerca tramite

Ricerca tramite

Testo completo


Diagrammi di Trattamento Termico sono disponibili per un notevole numero di materiali nel database Total Materia.

i diagrammi di Trattamento Termico coprono Temprabilità, Tempera/Durezza, TTT e CCT in accordo alle Normative di riferimento.

Per selezionare i materiali in base a proprietà speciali (es. Trattamento termico), è possibile utilizzare le caselle di controllo speciali di ricerca nel modulo di Ricerca Avanzata.

Per definire i criteri di ricerca, tutto ciò che si deve fare è selezionare il Paese e la Normativa di interesse dalla finestra a discesa Paese/Normativa e spuntare la casella di controllo 'Diagramma di Trattamento Termico', situato nella parte inferiore della pagina Ricerca Avanzata.

Fare clic su Invio.

Dopo aver selezionato la lega che interessa, si deve cliccare sul link "Trattamento Termico" per visualizzare i dati per il materiale selezionato. Il numero di records di Trattamento Termico viene visualizzato tra parentesi accanto al link.

Tutte le informazioni disponibili di Trattamenti Termici verranno visualizzate per il materiale scelto.

Per consentirvi di testare il Database Total Materia "senza impegno", vi invitiamo a unirvi alla comunità degli Utenti registrati per i test gratuiti a Total Materia.