Plasma Arc Welding of Titanium alloys

Extrait:

Welding of titanium can be relatively complex since at high temperatures the material can be very reactive and depending on the inclusion of impurities, they can also have a negative effect on overall weld integrity.
Key advantages of PAW compared to TIG include, lower heat inputs, high welding speeds and high metallurgical quality levels.

For successful welding of titanium, some factors need to be considered. Titanium is extremely reactive in temperatures exceeding 500-650°C. It reacts with elements in impurities or air such as C, O, N, and H. These elements strengthen titanium but small amounts also impair ductility and toughness of titanium joints. The effects of the heating and cooling cycles involved in welding processes on the mechanical properties of the alloys and the specific alloy composition also need to be considered.

Titanium alloys are readily joined with several common fusion welding processes such as tungsten inert gas welding (TIG), plasma arc welding (PAW), electron beam welding (EBW), and laser beam welding (EBW). Fusion welding processes can be characterized generally by the heat-source intensity.

The most common welding techniques to joint titanium and its alloys are Gas Metal Arc Welding (GMAW), such as Metal Inert Gas (MIG); Plasma Arc Welding (PAW); Laser Beam Welding (LBW); and Electron Beam Welding (EBW). The first three methods fall in the arc welding category with high heat input and low power density of heat source, while the last two techniques belong to the high-energy beam group.

Plasma arc welding (PAW) is an arc welding process which uses a constricted arc between a non-consumable electrode and the workpiece (transferred arc mode) or between the electrode and the nozzle (non-transferred arc mode). Two separate gas flows are used in PAW; plasma gas which flows through the orifice and becomes ionized and shielding gas which flows through the outer nozzle. Usually these gases are the same. Helium, argon and their mixtures are used as shielding gases. Hydrogen and nitrogen may also be added in the mixture. PAW is essentially an extension of the TIG welding process and the differences between the processes are illustrated in Figure 1. TIG uses an open arc while in PAW, the electrode and arc are surrounded by a gas chamber. The plasma gas in the orifice gets heated and ionized which creates a narrow, constricted arc that provides excellent directional control and produces a very favorable depth-to width weld profile.



Figure 1: The plasma arc is confined in PAW which makes it straighter and more concentrated

PAW can be used in two distinct operating modes, the melt-in mode and the keyhole mode. At lower arc currents, the process resembles TIG and produces a similar weld pool. This melt-in mode is used for material thicknesses below 3 mm. At higher arc currents and plasma gas flow rate, the plasma column can displace the molten metal and form a keyhole. Keyhole mode welding is used for single pass butt welds on material thicknesses from 2.4 mm to 8 mm. Compared to laser welding and electron beam welding, keyhole PAW is more cost effective and more tolerant of joint preparation, though its energy is less dense and its keyhole is wider.

The advantages of PAW compared to TIG include:
• High welding speed: up to 5 times higher than conventional TIG
• Reliable arc ignition and concentrated stable arc with little sensitivity to arc length variation
• Lower heat input leading to smaller heat affected zone and little distortion
• Ability to perform keyhole welding and melt-in-mode welding with the same equipment
• Possibility to weld very thin materials (0.1 mm) and thick materials (8 mm) with a single pass without filler material
• High metallurgical quality in comparison to conventional TIG.

PAW can be used to weld the same materials as TIG. Keyhole plasma welding is extensively used to weld stainless steel pipes and tanks. In aerospace industry, PAW is used for airframe components, fuel vessels and gas turbine components. The greater capital cost and complexity of PAW equipment are why PAW has not become more common.


References

1. S. Tolvanen: Microstructure and mechanical properties of Ti-6Al-4V welds produced with different processes, ISSN 1652-8891 Technical report no 109/2016 Department of Materials and Manufacturing Technology Chalmers University of Technology SE-412 96 Gothenburg Sweden, Accessed AUG 2019;

2. J. M. Sánchez-Amaya, T. Pasang, M. R. Amaya-Vazquez, J. De Dios Lopez-Castro, C. Churiaque, Y. Tao, F. J. Botana Pedemonte: Microstructure and Mechanical Properties of Ti5553 Butt Welds Performed by LBW under Conduction Regime, Metals 2017, 7, 269; doi:10.3390/met7070269

3. T. Pasang, Y. Tao, O. Kamiya, Y. Miyano, G. Kudo: Research on Various Welding Methods on Aerospace Titanium Alloys, Collaboration between Akita University and AUT University, Accessed AUG 2019.

Recherchez dans la base de connaissance

Entrer une phrase à rechercher:

Rechercher par

Texte entier
Mots-clés

En-têtes
Extraits

The Total Materia database contains many thousands of materials suitable for welding applications across a large range of countries and standards.

Where available, full property information can be viewed for materials including chemical composition, mechanical properties, physical properties and carbon equivalent data as well as advice on welding application.

Using the Advanced Search page, define the search criteria by selecting ‘Welding filler materials’ in the Group of Materials pop-up list. It maybe that you need to further narrow the search criteria by using the other fields in the Advanced Search page e.g. Country/Standard.

Then click Submit.

solution img

A list of materials will then be generated for you to choose from.

solution img

After clicking a material from the resulting list, a list of subgroups derived from standard specifications appears.

From here it is possible to view specific property data for the selected material and also to view similar and equivalent materials in our powerful cross reference tables.

solution img

Click on the property data link of interest to you to view specific property data.

solution img

For you’re a chance to take a test drive of the Total Materia database, we invite you to join a community of over 150,000 registered users through the Total Materia Free Demo.