Fatigue Behavior of Al-Si-Mg Alloys: Part Two


The fatigue behavior of a material is usually determined by conducting axial (tension and compression) and sometimes torsional fatigue experiments at the service temperature.
Between the temperatures of 150°C and 250°C the material strength decreases rapidly for almost all of the cast aluminum alloys as expected.

Failure of engineering components due to fatigue is a common occurrence in the aerospace and automotive industries. It is necessary to characterize the fatigue behavior of materials so that the engineering components can be operated safely and reliably.

The fatigue behavior of a material is usually determined by conducting axial (tension and compression) and sometimes torsional fatigue experiments at the service temperature. In reality, however, engineering components are subjected to loads in multiple directions, and these loads produce complex states of stress and strain within the component.

L. P. Borrego et al. investigated the influence of stress ratio and thickness on the fatigue crack growth rate. The research was conducted using AlCuMgSi (2017) aluminum alloy with a T4 heat treatment as well as AlMgSi1 (6082) aluminum alloys with a T6 heat treatment. The T4 and the T6 treatments are full heat treatment processes comprising of the operations of solution treatment, quenching and age-hardening. The age-hardening of the T4 heat treatment is performed at room temperature (naturally ageing) whilst in T6, this is performed by artificially ageing (160°C over 10 hours for 6082 aluminum alloy).

Fatigue tests were undertaken, in agreement with the ASTM E647 standard, using middle-tension, M (T), specimens.

The influence of stress ratio and thickness on the fatigue crack growth rate for aluminum alloy 2017-T4 can be seen in Figure 1. The data was obtained using a specimen thickness of 1.8 and 10 mm tested at stress ratios of R=0 and R=0.4. The fatigued fracture surface of 10 mm thickness specimen tested under R=0 is superimposed in the figure for comparison.

A strong R-ratio effect on the fatigue crack growth rate was observed for 1.8 mm thickness specimens. The same behavior was also observed for 10 mm thickness specimens, but only for ΔK values lower than 9 MPa m1/2. The crack growth rate da/dN generally increases with the stress ratio R.

Figure 1: Effect of stress ratio and specimen thickness on fatigue crack growth rate for alloy 2017-T4

Figure 2 shows that specimen thickness has no significant influence in the crack growth behavior of this alloy except for R=0 and for ΔK values above 9 MPa m1/2.

In the work done by M.B.Grieb et al., the monotonic tensile tests of the aluminum cast alloys were carried out at room temperature after the standardized specimens had been pre-aged at defined temperatures for 500 hours in order to determine the effect of aging on the tensile strength properties of the aluminum alloys examined.

500 hours were used to establish a completely over-aged material condition at least at the highest temperatures applied. The presented values of the ultimate tensile strength in Figure 2 are the mean values from five performed tensile tests.

Between the temperatures of 150°C and 250°C the material strength decreases rapidly for almost all of the cast aluminium alloys as expected. Only in the case of AlMg3Si1(Sc,Zr)-T5, the annealing is very much delayed, even at the highest temperature of 350°C.

AlSi7Mg-T7 shows the highest reduction of the tensile strength with temperature. After 500 hours at an aging temperature of 200°C or higher, the tensile strength has reached a minimum, and there with a stable condition. At temperatures of 150°C and higher, more and more incoherent Mg2Si particles are formed from coarsening, explaining the strength decreases of the AlSiMg alloys.

At 200°C and higher incoherent Al2Cu appears and reduces the tensile strength in the case of AlSiCu. Al3Sc is responsible for precipitation-strengthening in AlMg3Si(Sc,Zr)-T5 and is stable up to 300°C. Hence, it can be summarized that strength reduction due to aging is slow for this alloy.

Figure 2: Ultimate tensile strength of aluminum castings at room temperature as a function of preaging temperature after 500h aging

Various hardenable cast aluminium alloys (AlSi7Mg-T6, AlSi5Cu3-T7, AlSi5Cu1-T7, AlMg3Si1-T6, AlMg3Si1(Cu)-T6 and AlMg3Si1(Sc,Zr)-T5) have been studied and compared regarding their applicability as diesel engine cylinder heads.

The focus of the study is put on the resistance against thermomechanical fatigue (TMF) loading, which is typical of the cylinder head application, and the development of an accurate TMF life prediction model, which takes the change of the mechanical properties during TMF into account.

A near-component-shaped specimen, the so called “valve bridge sample” was developed and TMF tested in a special testing system which closely matches the real component loading situation. Furthermore the thermal and mechanical properties of the alloys were determined as a function of time, temperature and number of TMF loading cycles.

The mechanical properties obtained in tensile tests on standardized specimens after 500 hours of annealing at various aging temperatures indicate that the influence of the aging temperature is high for AlSi7Mg-T6 and low for AlMg3Si1(Sc,Zr)-T5 compared to the other aluminum alloys studied.

Furthermore, the TMF tests on the valve bridge samples showed that the AlSiCu alloys possess a higher resistance against TMF crack initiation in terms of the number of TMF cycles necessary to form a detectable fatigue crack as compared to AlMgSi and the AlSiMg alloys. The aging of the microstructure, due to the combined thermal exposure and cyclic plastic deformation occurring in the TMF tests, was proven macroscopically by 2-dimensional hardness measurements on the surface which are heated in the TMF loading system, and microstructurally by TEM examinations of samples taken from the critical location of the valve bridge samples.

It could be shown that a simplified aging model, which reproduces the decrease of the mechanical strength during TMF loading, can improve the thermomechanical fatigue life time prediction. For this purpose, two life time prediction models (IWM Freiburg and a simplified Chaboche model) were used to assess the TMF life time until crack initiation of the valve bridge samples.

Several numerical simulations with different assumptions for the mechanical properties, i.e. constant values related to the starting condition, constant values from the final condition and changing values according to the aging model, were run for TMF loading of near-component-shaped specimens made of the aluminum alloys AlSi7Mg and AlSi5Cu3.

The resulting life times were compared with the experimental results of the TMF tests. The comparison showed that the incorporation of the aging model improves the predictive capability and accuracy of both damage evolution models. This holds true in particular for AlSi7Mg, since the mechanical properties of this alloy change rapidly within the temperature range of the TMF loading.

Durchforschen Sie bitte den Informationsteil der Datenbank

Geben Sie bitte eine Anfrage, um Suche einzuleiten:

Suche nach

Vollständiger Text


Dieser Artikel ist Teil einer Artikelserie. Klicken Sie die Links um mehr über dieses Thema zu lesen.

Total Materia Extended Range, beinhaltet die größte Datenbank von Ermüdungs- und zyklischen Daten für tausende von Werkstoffen mit verschiedenen Wärmebehandlungsverfahren und Belastungsbedingungen. Belastungs- und Spannungsparameter werden angezeigt und gleichbleibende Eigenschaften sind als Referenz hinzugefügt, wie auch statistische Kennzahlen und Abschätzungen, wo passend.

Finding cyclic properties in the database is very easy and takes only seconds.

Zyklische Eigenschaften in der Datenbank zu finden ist einfach und sekundenschnell.

Geben Sie den gesuchten Werkstoff in das Feld der Schnellsuche ein. Sie können auch, falls erwünscht, Ihre Suche weiter einschrenken indem Sie eine Norm/Land in das vorgesehene Feld eingeben, bevor Sie Ihre Suche absenden.

Nachdem Sie den Werkstoff der Sie interessiert, ausgesucht haben, klicken Sie auf den Link der Ermüdungsdaten um die Daten für diesen Werkstoff zu sehen. Die Anzahl der zur Verfügung stehenden Ermüdungsdaten ist neben dem Link, in Klammern, angegeben.

Da Total Materia Ermüdungsdaten unabhänig von den Normen sind, können Sie diese anzeigen indem Sie auf den entsprechenden Link jedweder Untergruppe klicken. Die Wiederholungen bis Bruch, sowie die Belastungsamplitude sind in Tabellenform angegeben, mit Schaubild, wo passend.

Für jeden Datenset sind die Referenzen der Datenquellen angegeben. Sehen Sie untenstehend ein Beispiel.

Um unsere Datenbank auszuprobieren, laden wir Sie ein sich unserer Nutzergemeinschaft von über 150 000 angemeldeten Benutzern, mit einem kostenlosen Probeaboanzuschliessen.