PROPRIETARY HG 2631 Werkzeugstähle
Datenaktualisierungen
Dieser Werkstoff verfügt über 30 Eigenschaften – hier wird nur ein Teil davon angezeigt.
Erhalten Sie Zugriff auf alle Werkstoffeigenschaften, einschließlich detaillierter Werte für verschiedene Temperaturen und Zustände.
Kostenlose Registrierung erforderlich • Sofortiger Zugriff
PROPRIETARY HG 2631 Chemische Zusammensetzung
Cold Work Tool Steels, HG2510, Huang Limited, 2017
Suchen Sie nach vollständigen Daten für Werkstoffe?
Kostenlose Registrierung erforderlich • Sofortiger Zugriff
PROPRIETARY HG 2631 Physikalische Eigenschaften
Temperatur
Dieser Werkstoff verfügt über 30 Eigenschaften – hier wird nur ein Teil davon angezeigt.
Erhalten Sie detaillierte physikalische Werte für verschiedene Temperaturen und Bedingungen.
Kostenlose Registrierung erforderlich • Sofortiger Zugriff
PROPRIETARY HG 2631 Wärmebehandlung
- Forging:
Preheat at 650-680°C before raising the temperature to 1050-1100°C and soak until uniformly heated. Initial hammer blows should be light due to the comparatively high hot strength of this steel. The forging temperature must be maintained above 1000°C until the metal begins to yield. Final forging should not be done below 900°C. Slow cooling after forging is essential to avoid the possibility of cracking.
Annealing:
Heat at a rate not exceeding 400°F per hour (222°C per hour) to 1550°F (843°C), and hold at temperature for 1 hour per inch (25.4mm) of maximum thickness; 2 hours minimum. Then cool slowly with the furnace at a rate not exceeding 50°F per hour (28°C per hour) to 1000°F (538°C). Continue cooling to ambient temperature in the furnace or in air.
Stress Relieving:
To minimize internal stresses in cross sections greater than 6 inches (152.4 mm) and to improve stability in tools that will be EDM’d after heat treatment, a soaking time of 4 to 6 hours at the tempering temperature is strongly recommended.
Hardening:
Preheating: Heat at a rate not exceeding 400°F per hour (222°C per hour) to 1400-1450°F (760-788°C) and equalize. Austenitizing (High Heat): Heat slowly from the preheat. Furnace or salt: 1825-1850°F (996-1010°C). Soak for 30 minutes for the first inch (25.4 mm) of thickness, plus 15 minutes for each additional inch (25.4 mm). Quenching: Air, pressurized gas, or interrupted oil to 150-125°F (66-51°C). Note: Sizes over 5 inches (127 mm) in cross section may not achieve full hardness by cooling in still air. It is usually necessary to increase the quench cooling rate between 1400 to 900°F (760 to 482°C) by using an air blast, pressurized gas, or an interrupted oil quench. For the oil quench, quench until black, about 900°F (482°C), then cool in still air to 150-125°F (66-51°C).
Tempering:
Temper immediately after quenching. Hold at temperature for 1 hour per inch (25.4 mm) of thickness, 2 hours minimum, then air cool to ambient temperature. The typical tempering range is 300 to 600°F (149 to 316°C). Double tempering is recommended for tempering temperatures of 900°F (482°C) and higher.
PROPRIETARY HG 2631 Internationale Werkstoffäquivalente
4 von 11 Ergebnissen werden angezeigt.
Äquivalenzkategorien basieren auf dem Vergleich der chemischen Zusammensetzung und der mechanischen Eigenschaften — prüfen Sie die Eignung immer anhand der maßgeblichen Spezifikation für Ihre Anwendung.
Benötigen Sie die vollständige Liste von 11 internationalen Äquivalenten?
Sehen Sie alle 11 äquivalenten Werkstoffe mit detaillierter Zuordnung nach Norm, Hersteller und Äquivalenzkategorie.
Kostenlose Registrierung erforderlich • Sofortiger Zugriff
Optimieren Sie die Materialauswahl für Ihre Anwendung - Demo vereinbaren
- 11Querverweise
- 8Zusammensetzung
- -Mechanische Eigenschaften
- 3Physikalische Eigenschaften
- 2Wärmebehandlung
- -Metallographie
- -Zerspanbarkeit
- -Spannung-Dehnung
- -Umformbarkeit
- -Ermüdung
- -Fraktur
- -Schleicher
- -Verbindungen
- -Beschichtungen
- -Abmessungen
- -Tribologie
- -Korrosion
- -Alterung
- -Witterungsbeständigkeit
- -Bestrahlung
- 6Gesamtzahl der Lieferanten