Heat-resisting steels

Sažetak:

Steels are now used for a wide variety of conditions entailing heat and corrosion under both static and dynamic stresses, such as aero engine valves, furnace conveyers, retorts, oil cracking units and gas turbines. Three important properties are necessary in material used at elevated temperatures:
1. Resistance to oxidation and to scaling.
2. Retention of strength at the working temperature.
3. Structural stability as regards carbide precipitation, spheroidisation, sigma formation and temper embrittlement.

Steels are now used for a wide variety of conditions entailing heat and corrosion under both static and dynamic stresses, such as aero engine valves, furnace conveyers, retorts, oil cracking units and gas turbines. Three important properties are necessary in material used at elevated temperatures:

1. Resistance to oxidation and to scaling.
2. Retention of strength at the working temperature.
3. Structural stability as regards carbide precipitation, spheroidisation, sigma formation and temper embrittlement.

Other properties may also be important in particular applications, such as specific resistance and temperature coefficient for electrical purposes, coefficient of expansion for constructional units and resistance to penetration by products of combustion in many furnace applications. In the case of gas turbine steels additional characteristics have to be considered; internal damping capacity and fatigue strength, notch sensitivity and impact strength (hot and cold), machining and welding characteristics, especially as large rotors may have to be built of small sections welded together.

The scale which forms on iron is porous and loosely adherent, but it is rendered adherent and protective by the addition of certain elements to the steel. These are usually chromium, silicon and aluminium, and they are characterised by their great affinity for combining with oxygen, but the reaction is rapidly stifled by the formation of the inert oxide films.

The resistance of mild steel to oxidation is vastly improved by forming an aluminium-iron alloy on the surface. This is done by heating at 1000°C in contact with powdered aluminium (calorising) or by metal-Spraying the steel surface with aluminium, coating with bitumastic paint to prevent oxidation and heating to 780°C (aluminising).

Improved creep strength may be attained by

  •  raising the softening temperature by the solution of alloying elements;
  •  
  •  judicious use of precipitation hardening at the working temperature without readily over-ageing. Second phase hardening is critically dependent on the degree and uniformity of the dispersion achieved and creep rate is related to a critical range of particle spacing;
  • controlled degree of work-hardening in the appropriate temperature ranges which often reduces the extent of the primary creep stage;
  • variations in the process of manufacture; deoxidisers and particles in the crystal boundary can have a marked effect on creep properties;
  • vacuum melting permits the use of advantageous compositions which cannot be melted by conventional methods. lt also improves ductility in the transverse direction.

Mechanical properties, are improved by the addition of various elements.
Cobalt, tungsten and molybdenum cause the steels to withstand the action of tempering. High alloy austenitic steels have no change points and therefore do not harden by air cooling, but their resistance to wear resistance is not great. A sufficiency of elements such as silicon and chromium raise the Ac, point to temperatures above those reached in service and prevent the steel from air hardening on cooling.

Steels with high nickel content should not be used at high temperatures in contact with gases containing sulphur dioxide or other sulphur compounds, since intercrystalline films of nickel sulphide are formed.

In high chromium steels the carbides coalesce into large particles which have less obstructive action on grain growth of the ferrite at temperatures above 700°C. The excessive grain growth reduces still further the toughness which these steels possess.

Grain growth also occurs in the austenitic steels above 1000°C, but no trouble arises since they remain tough and ductile even in the coarse grained condition. When heated in the range 500-900°C austenitic steels precipitate carbides along the boundaries of the austenite and as a result intercrystalline cracks are liable to develop if the steel is stressed continuously in tension in this temperature range. With certain compositions both ferritic and austenitic steels are embrittled by the formation of sigma phase.

Pretražite bazu znanja

Unesite reč za pretragu:

Pretražite prema

Kompletan tekst
Ključne reči

Naslovi
Sažetak

Total Materia ima podatke o mehaničkim osobinama za više hiljada materijala i pristup njima je na samo klik od Vas.

Pokriva veliki broj podataka o osobinama, pa je lako pronaći granicu tečenja, zatezni napon elongaciju za veliki broj materijala u našoj bazi.

Unesite materijal u polje Brza pretraga. Pretragu možete suziti odabirom zemlje/standarda, a nakon toga kliknite na Pretražite.

solution img

Total Materia kreira listu rezultata iz koje možete odabrati materijal koji vas zanima.
Kliknite na materijal koji ste odabrali.

solution img

Da biste videli podatke o mehaničkim osobinama kliknite na link Hemijski Sastav na stranici podgrupe. Broj zapisa o mehaničkim osobinama se prikazuje u zagradama pored linka.

solution img

Uz mehaničke osobine prikazuju se i osnovne informacije o odabranom materijalu.

Mehaničke osobine su prikazane za različita stanja i vidove termičke obrade.

solution img

Takođe, moguće je birati između metričkog sistema (SI) i anglosaksonskog sistema jedinica, zavisno od Vaše pretrage.

solution img

Imate priliku da isprobate Total Materia bazu podataka. Pozivamo Vas da se pridružite zajednici od preko 150,000 registrovanih korisnika kroz Total Materia Besplatan demo.