Plasma Transferred Arc Welding

Sumário:

The Plasma Transferred Arc welding technique is an evolutionary development of the more widely used Gas Tungsten Arc Welding process.
Using a constrictor nose to harness and concentrate very high energy and restricting the electric arc using various gas control methods, PTAW is highly effective for specific welding cases.

The Plasma Transferred Arc (PTA) process employs the plasma principle hence it may be considered an evolution of the Gas Tungsten Arc Welding (GTAW) process, where the high-energy concentration is due to the use of a constrictor nose, which restrains the column diameter of an electric arc established between a tungsten electrode and the workpiece in an inert gas atmosphere, usually argon.

The feeding material is carried to the plasma jet by a gas stream, which might be inert, active or a mixture of active and inert gases. A third gas flow is employed to protect the metal pool from atmospheric contamination. Even though there is the possibility of using mixtures of active and inert gases, argon is typically employed for all three-gas systems.

The PTA process can be considered a derivation of the PAW process. The similarities between the two processes can be observed in Figure 1. Both welding processes employ a non-consumable tungsten electrode located inside the torch, a water-cooled constrictor nozzle, shield gas for the protection of the molten pool, and the plasma gas. The difference between the two welding processes lies in the nature of the filler material, powder instead of wire, which requires a gas for its transport to the arc region. The diagram in Figure 1 shows the two processes with their differences and similarities.



Figure 1: Comparison of Plasma Transferred Arc processes and PAW

As mentioned above, the PTAW welding process and equipment are a modification of Gas Tungsten Arc Welding (GTAW). The significant difference involves a redesign of the GTAW torch to provide a concentration and collimation of the arc plasma. This is achieved by generating the arc and its plasma within the confines of the torch followed by discharging the high temperature ionized plasma through an orifice.

The diameter, configuration and throat length of the orifice are carefully designed to maximize the desirable properties of the arc, i.e. culmination, high temperature and stability. Orifice details are interchangeable so that variations in these dimensions are available to satisfy a variety of weld requirements. The orifice concentrates the plasma arc and collimates the flow so that it assumes a beam configuration as opposed to the "umbrella" shaped arc of the GTAW process.



Figure 2: Schematic view of Plasma Transferred Arc (PTA) Welding

Applications:

  • Hard Surfacing: PTAW is well suited to apply hard alloys for wear resistance. Stellite, Colmonoy, Hastelloy, and Tungsten Carbide can all be successfully applied with PTAW.
  • Corrosion Resistant Overlays: The localize heat input characteristics of PTAW allow corrosion resistant alloys to be applied with very little dilution into the base material. PTAW can achieve subsea chemistry requirements of <5% Fe in as little as 0.040” of overlay thickness.
  • Industries / Components:
    - Non-Mag Down Hole Tools: Drill Collars, Wear Bands for MWDs, Flex Ponies etc.
    - Down Hole Components: Mud Motor Bearings, Stabilizers, Topsubs, Piston SubsFlow Restrictors, Drill Bits etc.
    - Flow Control: Valve Bores, Gates, Seats, Seat Pockets, Ring Grooves, Valve Stems etc...
    - Power Generation: Turbine Blades, Shafts, Bearing Surfaces, etc.
    - Riser Equipment o Pins, Boxes, etc.


References

1. A.S.C.M.D’Oliviera, R.S.C.Paredes, R.L.C. Santos: Pulsed current plasma transferres arc hardfaccing, Journal of Materials Processing Technology 171, 2006, p.167–174;

2. V.V.Diaz, J.C.Dutra, A.S.C.D’Oliveira: Hardfacing by Plasma Transferred Arc Process, INTECH, Ed.W.Sudnik, 2011, ISBN 978-953-307-642-3;

3. P.V. Senthill, A.Shirrushti: Finite Element Simulation of Plasma Transferred Arc Welding [PTAW} of structural steel, PV Senthiil Int. Journal of Engineering Research and Applications www.ijera.com ISSN : 2248-9622, Vol. 4, Issue 10(Part - 4), October 2014, p.06-11;

4. What is Plasma Transferred Arc Welding [PTAW], 1/12/15, js, Accessed Oct 2015;

Procurar conhecimento básico

Colocar uma frase para procurar por:

Procurar por

Texto completo
Palavras chaves

Títulos
Resumo

O banco de dados da Total Materia contém muitos milhares de materiais adequados para aplicações de soldagem através de uma grande variedade de países e padrões.

Quando disponíveis, informações de propriedade completa pode ser vista de materiais incluindo a composição química, propriedades mecânicas, propriedades físicas e dados equivalentes de carbono, bem como conselhos sobre a aplicação de solda.

Usando a página de pesquisa avançada, definir os critérios de pesquisa através da selecção dos materiais de soldadura de enchimento 'no Grupo de Materiais lista pop-up. É talvez o que você precisa para estreitar ainda mais os critérios de pesquisa usando os campos na página de pesquisa avançada por exemplo, País / Standard.

Em seguida, clique em Enviar.


Uma lista de materiais será então gerado para você escolher.


Depois de clicar em um material a partir da lista resultante, uma lista de subgrupos derivados de especificações padrão aparece.

A partir daqui é possível ver os dados de propriedades específicas para o material selecionado e também para ver os materiais semelhantes e equivalentes em nossas poderosas tabelas de referência cruzada.


Clique no link de dados propriedade de seu interesse para ver os dados de propriedade específicos.


Para você é uma oportunidade de fazer um test drive na Total Materia, nós convidamos você a participar de uma comunidade de mais de 150.000 usuários registrados através da Total Materia Free Trial.