AISI Designation system

요약:

The American Iron and Steel Institute has established a designation system for structural shapes, which has been adopted by steel producers. A four-numeral series is used to designate graduations of chemical composition of carbon steel. The first two digits indicate the grade of carbon steel. The last two numbers are intended to indicate the approximate middle of the carbon range. For example, in the grade designation 1035 represents a carbon range of 0.32% - 0.38%.

The American Iron and Steel Institute has established a designation system for structural shapes, which has been adopted by steel producers. A summary of the AISI designations is shown below.

"W" SHAPES are doubly-symmetric wide flange shapes used as beams or columns whose inside flange surfaces are substantially parallel. A shape having essentially the same nominal weight and dimensions as a "W" shape, but whose inside flange surfaces are not parallel, may also be considered a "W" shape, provided its average flange thickness is essentially the same shape as the flange thickness of the "W" shape.

"S" SHAPES are doubly-symmetric shapes produced in accordance with dimensional standards adopted in 1896 by the Association of American Steel Manufacturers for American Standard beam shapes. The essential part of these standards is that the inside flange surfaces of American Standard beam shapes have approximately a 16 2/3% slope.

"M" SHAPES are doubly-symmetric shapes that cannot be classified as "W", "S", or bearing pile shapes. Although not included in the standard nomenclature tabulation, bearing piles are doubly-symmetric wide flange shapes whose inside flange surfaces are essentially parallel and whose flange and web have essentially the same thickness.

"C" SHAPES are channels produced in accordance with dimensional Standards adopted in 1896 by the Association of American Steel Manufacturers for American Standard channels. The essential part of these standards is that the inside flange surfaces of American Standard channels have approximately a 16 2/3% slope.

"MC" SHAPES are channels that cannot be classified as "C"shapes.

DESIGNATION OF CARBON STEELS AISI/SAE

DEFINITION. Steel is considered to be carbon steel when no minimum content is specified or required for aluminum, chromium, cobalt, columbium, molybdenum, nickel, titanium, tungsten, vanadium, or zirconium, or any other element added to obtain a desired alloying effect; when the specified minimum for copper does not exceed 0.40%; or when the maximum content specified for any of the following elements does not exceed the percentages noted: manganese 1.65, silicon 0.60, copper 0.60.

NUMBERING SYSTEM. A four-numeral series is used to designate graduations of chemical composition of carbon steel. The first two digits( Table 1.) indicate the grade of carbon steel. The last two numbers are intended to indicate the approximate middle of the carbon range. For example, in the grade designation 1035 represents a carbon range of 0.32% - 0.38%.

It is necessary, however, to deviate from this system and to interpolate numbers in the case of some carbon ranges and for variations in manganese, phosphorus or sulfur within the same carbon range.

Within the numerical designation system the special-purpose elements lead and boron are commonly designated by inserting the letter "L" or "B" respectively between the second and third numerals of the AISI number, e.g., 10L45 and 10B46.

The prefix "M" indicates "merchant quality". The "M" grades are produced to wider carbon and manganese ranges than the corresponding standard grades which are not so prefixed.

Grade Description
10XX Non-resulfurized Carbon Steels, Manganese 1.00% maximum
11XX Resulfurized Carbon Steels
12XX Rephosphorized and Resulfurized Carbon Steels
15XX Non-resulfurized Carbon Steels, Manganese max. over 1.00%
*First two digits indicate grade of carbon steel.
**Last two digits represent middle of carbon range.

Table 1. Designation of carbon steels

기술 자료 검색

검색할 어구를 입력하십시오:

검색 범위

본문
키워드

머릿글
요약

Total Materia로, 금속 표준 규격 사양, 그것의 현 상태와 정의하는 자료에 대한 정보를 검색하는 것은 매우 간단합니다.

몇 초 이내에 Total Materia 규격 리스트에서 관련 세부 소재 특성 데이터 또는 등가 재질을 검색하는 것이 가능합니다.

시작하시려면, 메뉴 표시줄의 규격 리스트 버튼을 클릭합니다.


단순히 표준 개발 기구(SDO)를 선택하거나 표준 번호 또는 키워드를 입력하시기만 하면, 30,000 이상의 규격과 다국어 데이터베이스에서 즉각적으로 결과를 받을 수 있습니다.

예를 들어, 팝업에서 이 SDO를 선택하여 SAE에 있는 모든 금속 규격을 검토할 수 있습니다.


결과 목록은 1600개의 재질, SAE개의 금속 규격으로 구성되어 있습니다. 포함 정보: 규격 설명, 마지막 발행 해, 현재의 상태 (유효, 교체 등), 및 규격에 의해 정의된 재질들의 핫 링크로 구성되어 있습니다.


단순히 재질의 링크를 클릭하시면, 선택한 규격에 의해 정의된 금속 재질의 목록을 볼 수 있습니다.


재질의 목록에서, 각 재질의 자세한 특성과 등가물을 검토하실 수 있습니다.


Total Materia 데이터베이스를 사용해 보실 수 있는 기회가 있습니다. 저희는 Total Materia 무료 체험을 통해 150,000명 이상의 사용자가 이용하고 있는 커뮤니티로 귀하를 초대합니다.