The Cold Forging Process: Part Two

요약:

Forging is one of the oldest metal working practices in existence and was primarily used as far back as 4000 B.C. to make jewelry, coins and various other items.
In the modern day however there are now a whole host of possibilities to reduce the number of issues in what is an inherently high defect forming process including micro-scale modeling techniques which compute the micro-structural evolution during the forming process.

Forging is a process in which the work piece is shaped by compressive forces applied through various die and tools. It is one of the oldest methods in metalworking operations, dating back to at least 4000 B.C. Forging was first used to make jewelry, coins and various implements by hammering metal tools made of stone. In practice there is a wide range of defects which occur during metal forming processes.

Fracture is in most cases the only defect that immediately is recognized as one. In literature there are several manners mentioned to avoid defects. Statistical process control and various physical modelling techniques are the methods that are already being frequently used in industry. Databases, expert systems and neural networks however, are not being used so often but they show great potential on defect avoidance. On the other hand, different authors made an attempt to optimize the die design and to achieve the quality of forged part, for that they have used different techniques, like FEM, Neural Network, etc.

Computer simulation has become reliable and acceptable in the metal forming industry since the 1980’s. Metal forming analysis can be performed in three modeling scales. The first scale is the global modeling, which only predicts process loads or work. Analytical methods are used for this purpose. Local scale analysis is used to estimate the thermo-mechanical variables such as strain, strain rate, and temperature.

With the extensive development in computational mechanics, numerical methods have been used as an economical alternative to perform the local modeling. Micro-scale modeling computes the micro-structural evolution during the forming process. Since global scale analysis is only applicable to simple situations and micro modeling is still incipient and only gives results for specific conditions, local modeling is the most popular approach. Among other methods, the Finite Element Methods (FEM) is widely used in metal forming analysis due to its capabilities to model the complicated geometries of tools and parts in forming processes.

One of the biggest challenges in the metal forming industry is to obtain products in the final shape and properties with minimum machining. Cold forging processes are a viable option for this purpose because the manufactured part needs little machining, small production time, and the products present mechanical strength higher than parts manufactured by other processes.

Cold forging is a process carried out below the recrystallization temperature applied to manufacture small parts with varied geometries and has the following advantages: minimum material waste, mechanical properties improvement, such as yield strength and hardness, which brings as an advantage the use of cheaper materials, very good surface finish, energy economy when compared with hot or warm forging, and tools subjected to less thermal fatigue.

In the paper of Cristina Maria Oliveira Lima Roque and Sérgio Tonini Button, is presented two forming problems. Ring compression test and upsetting simulations are presented to demonstrate the capabilities of finite element commercial software (ANSYS) to aid in metal forming design. The contact conditions are modeled by the Coulomb law with a penalty method and the multilinear elasto-plastic material model is used. Experiments are carried out to validate the modeling technique.

Figure 1 shows how finite element analysis (FEA) can be used in metal forming design. FEA can provide detailed information for forming designers such as forming force, defects predictions, flow pattern, and stress concentration in the dies. The strain output, for instance, can display strain concentration areas to identify the possible early failures in the tools or to predict formability problems.

Therefore, part fabrication design can be modified to improve a tool’s life or for simulations before experimental tests. As conclusion they noted that numerical prediction of the final shape is in good agreement with the experimental results. Flow stress was predicted properly and the stress field is in accordance with the macro etching. The method was able to predict the filling sequence.



Figure 1: Flow chart showing the use of finite element analysis in a forging problem



Figure 2: Cold Forged Parts for Automotive components

기술 자료 검색

검색할 어구를 입력하십시오:

검색 범위

본문
키워드

머릿글
요약

이 문서는 전체 문서 중 일부분입니다. 이 주제에 대해 더 읽고 싶으시면 아래 링크를 클릭하시면 됩니다.

화학 조성을 Total Materia 데이터베이스에서 검색하는 것은 매우 쉽습니다.

몇 초 내로 데이터베이스 내 175,000개 이상의 재질에서 유용한 화학 조성 데이터를 검색하는 것이 가능합니다.

신속 검색에 검색할 재질명을 입력합니다. 원하신다면 국가/규격을 지정하신 후 검색 버튼을 클릭합니다.


Total Materia 데이터베이스에서 검색된 관심 재질의 목록이 즉시 생성됩니다.
관심 재질을 클릭합니다.


소그룹 페이지에서, 선택된 재질의 화학 조성 링크를 클릭하여 데이터를 검토합니다. 화학 조성 데이터 기록의 개수는 링크 옆 괄호 안에 표시됩니다.


화학 조성 데이터는 참조를 위해 선택한 모든 재질 정보와 함께 표시됩니다.


Total Materia 데이터베이스를 사용해 보실 수 있는 기회가 있습니다. 저희는 Total Materia 무료 체험을 통해 150,000명 이상의 사용자가 이용하고 있는 커뮤니티로 귀하를 초대합니다.