Power Supply for Welding Processes


Selection of a welding process is determined primarily by the characteristics of the joint, the materials involved, their shape and thickness, and joint design. Additionally, production requirements, such as rate and quality, must also be considered.
Only after the process has been determined can the proper power supply and accessory equipment be chosen. The process is the primary factor in their selection.

Selection of a welding process is determined primarily by the characteristics of the joint, the materials involved, their shape and thickness, and joint design. Additionally, production requirements, such as rate and quality, must also be considered. Only after the process has been determined can the proper power supply and accessory equipment be chosen. The process is the primary factor in their selection.

It is our purpose in this article to provide a guide to the selection of power supplies for some of the welding processes, which have come into maturity during the past decade. Once thought of primarily as special processes or processes designed primarily for mass production operations, they are now found in virtually every area of metal fabrication. The increase in the fabrication of once difficult-to-weld metals and the economic and qualitative advantages of the more advanced welding processes are today recognized by even the smallest metal fabricating shops.

Power and control requirements for these processes are somewhat more sophisticated than for conventional shielded metal arc or stick electrode welding. But since the average metallurgist or welding engineer isn’t an electrical expert, the selection of proper power supply and the reasons for it can be confusing. The purpose of this article is to eliminate some of this mystery through the examination of the power requirements of production welding processes.

The basic types of power supplies are:

  • constant current and
  • constant voltage.

Constant Current Power Supply

The conventional stick electrode welder is sometimes called a ’constant current machine’. It is also called a ’dropper’ because its voltage drops as welding current increases, thus its volt- ampere output curve ’droops’.

With the machine turned on but with no arc, and hence no current flowing, it has a relatively high open circuit voltage of 70-80 volts. Generally speaking welding is done at the steeper portions of the curve and this is ideal for manual stick electrode welding.

Arc voltage depends upon the physical length of the arc between the electrode and the work and this can never be held completely constant in manual welding. But, since rate of burn off of filler metal is determined by the amount of current, burn off stays substantially constant if current doesn’t vary.

There are many variations of this type of machine based upon power input (single or three phase), output (ac, dc, or ac/dc), and the type of output control (mechanical or electrical).

Constant Voltage Power Supply

The other basic type of arc welding power supply produces a constant voltage. Thus at any voltage setting current may vary from zero to an extremely high short circuit current. Such a machine is designed specifically for gas shielded metal arc welding and is not generally suitable for stick electrode welding.

Actually, no welding machine can produce a truly constant voltage. In practice, voltage drops at least 1 volt for each 100 amp output. Nevertheless, short circuit currents may be as high as several thousand amperes.

Normally, constant voltage machines have lower open circuit voltages than the constant current machines, about 50 volts maximum as compared to 80 volts. As a means of obtaining the desired arc voltage, the operator sets open circuit voltage, rather than current, at the machine. Settings may range from 10 to 48 volts.

Welding current can reach several thousand amperes at short circuit. Current adjusts itself to burn off filler metal at a rate sufficient to maintain the arc length required by the present voltage and is thus determined by the rate of electrode feed.

Duty Cycle

All welding machines are rated according to their duty cycle. Understanding this term is of utmost importance and it is often misunderstood. Duty cycle is based upon a ten minute time period. At rated voltage, a power supply with a 100% duty cycle rating can operate continuously at or below its rated current.

A 60% duty cycle does not mean that it can operate 60% of an indeterminate time at rated current and voltage. It means that the welder should operate only 6 out of every 10 minutes at that current and voltage. It should be allowed to idle 4 out of every 10 minutes for cooling. Machines rated for less than 100% duty cycle can be used continuously by decreasing their current rating.

Tungsten Arc Welding

Tungsten arc welding, using inert shielding gases, is hardly a new process. Nevertheless, it should be covered in any survey of advanced welding processes because of its particular applicability to difficult welding problems. This includes joining hard-to-weld and exotic materials such as the stainless steels, aluminum, magnesium, copper, beryllium copper, Hastelloy, Inconel, Invar and Kovar, especially in very thin cross sections.

Essentially, TIG welding calls for the same type of power source as shielded metal arc, or stick electrode welding, that is one with a drooping volt-ampere output curve. However, the process does present some problems which make a machine especially designed for the process much more suitable.

It should be noted that a conventional AC power source not specifically designed for TIG welding must be derated for AC TIG service. This is because partial rectification occurring at the arc introduces a DC component, which causes overheating of the main transformer. Other problems associated with TIG welding which are more acute than in conventional metallic arc work include arc starting, arc stabilization, and, of course, as the work becomes more delicate, control of all welding variables.

Gas Metal Arc Processes

Gas metal arc welding, in which a consumable wire electrode is fed continuously to a gas shielded arc zone, has replaced non-consumable tungsten inert gas welding and conventional shielded metal arc (stick electrode) welding in many applications. The main reason is its speed. Where it can be used, it is usually several times faster than other processes.

Other advantages include: cleaner welds, because the shielding gas greatly reduces and often prevents oxide formation; electrode savings through the virtual elimination of stub losses; excellent weld metallurgical and physical characteristics: and simplicity of operation which increases weld quality and reproducibility and generally reduces the human variable.

Arc Spot Welding

Arc spot welding has become very popular in recent decades. Its chief advantage is the ability to spot weld from one side of the work. In addition, it is a fast method of producing multiple spot welds with a high degree of reproducibility.

TIG Spot Welding

Arc spot welding may be performed either by tungsten inert gas or gas shielded metal arc processes. For tungsten spot welding the same type of power supply used for regular TIG welding may be employed. However, it requires a special spot welding gun and controls.

TIG spot welding involves the fusion of the parent metal only. Filler wire is not used. Generally TIG spot welding is performed on cold rolled and stainless steels.

MIG Spot Welding

Gas shielded metal arc spot welding is characterized by high amperages. Machines designed for this purpose normally have higher volts. Welding currents with smaller diameter wires up to about 1/16 in. may reach 500 amp. Wires 1/16 in. diameter and larger call for welding currents up to 750 amp. As in TIG spot welding, special controls are required. These are normally incorporated in a special wire drive and control unit.

Plasma Arc Welding

An extension of the commercially accepted plasma cutting technique and similar in some respects to the tungsten inert gas process, it has fewer limitations than such methods as electron beam, laser and ultrasonic welding and at far less initial cost.

Like tungsten inert gas welding, plasma welding is normally a fusion process although cold filler wire may also be employed, depending on the job. The electrode is tungsten coated and water cooled because of the high temperatures involved. The process differs from TIG welding in that, in addition to a shielding gas, a plasma forming gas is also involved. The plasma ’flame’, sometimes in combination with an electric arc can produce extremely high temperatures. The flow of the plasma can be focused by the design of the torch and as a result can be highly concentrated to produce deep, narrow penetration.

기술 자료 검색

검색할 어구를 입력하십시오:

검색 범위



Total Materia는 용접용으로 적합한 다양한 국가와 규격 내 수천개의 재질에 대한 정보를 포함하고 있습니다.

재질의 화학적 조성, 기계적 특성, 물리적 특성, 탄소 등가 데이터와 용접용으로 재질 이용 시 필요한 정보 등의 전체적인 특성 정보들을 어디서든 검토하실 수 있습니다.

고급 검색을 이용하여, 검색 조건의 재질 리스트에서 '용접 필러 재료'를 선택합니다. 검색 범위 좀 더 줄이기를 원하신다면 국가/규격과 같은 다른 조건을 지정할 수 있습니다.

검색 버튼을 클릭합니다.

선택된 정보에 부합하는 일련의 재질이 검색됩니다.

결과 리스트에서 재질을 선택하시면, 일련의 규격 사양 소그룹이 나타납니다.

여기에서 선택한 재질의 특정 특성 데이터를 검토하실 수도 있고, 강력한 상호 참조 표를 이용하여 유사 재질이나 등가 재질을 검토하는 것 또한 가능합니다.

자세한 특성 데이터를 보시려면 특성 데이터 링크를 클릭하세요.

Total Materia 데이터베이스를 사용해 보실 수 있는 기회가 있습니다. 저희는 Total Materia 무료 체험을 통해 150,000명 이상의 사용자가 이용하고 있는 커뮤니티로 귀하를 초대합니다.