Press Hardened Steels (PHS)

概要:

Press Hardening Steels (PHS) are a unique group of materials which are mostly comprised of different kinds of boron-alloyed manganese steels and gain wide application to produce high strength structural body elements.
As part of the AHSS group of steels, PHS play an important part in the ever increasing challenges of light weighting vehicles whilst maintaining durability and passive safety.

Environmental aspects have become extremely important when engineering new passenger cars. In order to reduce fuel consumption and toxic emissions, one step is to decrease the weight of the vehicle. Regarding the car body structure this means down-gauging of the sheet components and the introduction of more advanced high strength steels (AHSS) in order to maintain a high performance in terms of crashworthiness, durability etc.

The advanced high-strength steels (AHSS) help engineers meet requirements for safety, efficiency, emissions, manufacturability, durability, and quality at a low cost. AHSS are a newer generation of steel grades that provide extremely high-strength and other advantageous properties, while maintaining the high formability required for manufacturing. It was well known that AHSS have been on the road for many years, but with additional research and development, automakers are using these newer grades in more applications.

The AHSS family includes Dual Phase (DP), ComplexPhase (CP), Ferritic-Bainitic (FB), Martensitic (MS or MART), Transformation-Induced Plasticity (TRIP), Hot-Formed (HF), and Twinning-Induced Plasticity (TWIP).

Among the Advanced High Strength Steels, Press Hardening steels (PHS) form a unique group: these are mostly different kinds of boron-alloyed manganese steels and gain wide application to produce high strength structural body elements (e.g. A-and B-pillars, etc). Press Hardening Steels are widely used in car body manufacturing in hot forming processes.

To illustrate typical applications of AHSS, and press-hardened components in particular, are shown in Figure 1. Press-hardened components are in red color, otherwise indicated with arrows.



Figure 1: Automotive body structures. Press-hardened components are shown in red, otherwise indicated with arrows.

What are Press-Hardened Steels (PHS)?

Press-Hardened Steels are Boron added (.001%-.005%) Carbon /Manganese steels that have been in use since the mid 1980’s for automotive body in white construction. These steels are also known as HF or Hot Formed Steel.

The hot forming process of PHS steels

Hot forming of steels is a complex forming and tempering operation: it is often termed as hot press forming or press hardening of steels, too. The full austenitization of the material is regarded as the first step in hot press forming. Forming is performed is cooled down rapidly in the tool applying the critical cooling rate, hence resulting in martensitic microstructure.

To enable the Boron-alloyed steel material to be formed and further on cooled down to a fully martensitic structure, the material first has to be heated up to its austenitization temperature at around 880-950°C. To achieve a fully martensitic structure, the cooling rate must exceed 25-30°C/s. The small amount of Boron (~ 0.002 weight-%) is used to facilitate the quenching process, wherefore the material often is referred to as Boron steel in colloquial terms. (Figure 2).

The hot-forming process is mainly divided into two different approaches, the indirect and the direct one, where the direct process is the most commonly used among the automotive OEMs. These two processes offer different advantages for the final application in terms of design versus cost and available choices for surface protection.



Figure 2: Temperature vs. process time for hot press forming of PHS

Making the first forming step(s) by conventional cold forming, the indirect process offers the possibility for more complex geometries and undercut designs before the shaped components are heated, transferred to the oven and finally tempered (Figure 3). This means that two sets of tools are necessary, one for pressing and one for cooling. One advantage however, with this process, is that it offers the possibility to use a conventional zinc-based coating for cathodic corrosion protection.



Figure 3: Schematic description of the indirect hot-forming process. cold-forming of the blank in one or several steps, heating of the pressed part to roughly 900°C, rapid cooling of the part to achieve a martensitic structure, post processing like laser or tool cutting etc.


References

1. J. K Larsson: Optimizing the Resistance Spot Welding Process for High quality welding of Press-Hardened Automotive Components, Conference: EUROJOIN 8, Pula, Croatia, May 2012, Accessed DEC 2020;

2. S. A. Salihu: Assessment of Advanced High Strength Steels used in Auto Industry – A Review, 2016 IJSRSET, Volume 2, Issue 4, Print ISSN: 2395-1990, Online ISSN 2394-4099;

3. Development of lightweight steels for automotive applications, Accessed DEC 2020;

4. R. Östlund: Microstructure based modelling of ductile fracture in quench-hardenable boron steel, University of Technology Luleå, Luleå, Sweden, Doctoral Thesis in Solid Mechanics, ISSN: 1402–1757 ISBN: 978–91–7583–262–3 (print) ISBN: 978–91–7583–263–0 (electronic), Accessed DEC 2020.

ナレッジベース検索

検索したい語句を入力:

検索方法

全文一致
キーワード

前方一致
要約

Total Materiaデータベースでは膨大な数の材料熱処理状態図を見る事ができます。

熱処理状態図には焼入硬化性、焼き戻し硬化性、TTT, CCTが含まれ標準のデータベースベーシックに含まれております。

特殊な特性で材料を選ぶには高度な検索モジュールのチェックボックスを利用すると検索することができます。

まず検索条件を決めます。対象材料の国/規格を選び、高度な検索のページの下の特殊な検索のところにある ’熱処理状態図’ のチェックボックスにチェックを入れます。

確定をクリックします。


対象材料を選んでから熱処理のリンクをクリックするとその材料のデータを見る事ができます。熱処理データ記録の数はリンクの隣のカッコ内に表示されております。


選んだ材料の熱処理情報はすべて表示されます。






Total Materiaデータベースをあなたにテスト評価を頂くために15万人以上の方が登録されている無料お試しコミュニティ-へ御招待致します。