Plasma Transferred Arc Welding

概要:

The Plasma Transferred Arc welding technique is an evolutionary development of the more widely used Gas Tungsten Arc Welding process.
Using a constrictor nose to harness and concentrate very high energy and restricting the electric arc using various gas control methods, PTAW is highly effective for specific welding cases.

The Plasma Transferred Arc (PTA) process employs the plasma principle hence it may be considered an evolution of the Gas Tungsten Arc Welding (GTAW) process, where the high-energy concentration is due to the use of a constrictor nose, which restrains the column diameter of an electric arc established between a tungsten electrode and the workpiece in an inert gas atmosphere, usually argon.

The feeding material is carried to the plasma jet by a gas stream, which might be inert, active or a mixture of active and inert gases. A third gas flow is employed to protect the metal pool from atmospheric contamination. Even though there is the possibility of using mixtures of active and inert gases, argon is typically employed for all three-gas systems.

The PTA process can be considered a derivation of the PAW process. The similarities between the two processes can be observed in Figure 1. Both welding processes employ a non-consumable tungsten electrode located inside the torch, a water-cooled constrictor nozzle, shield gas for the protection of the molten pool, and the plasma gas. The difference between the two welding processes lies in the nature of the filler material, powder instead of wire, which requires a gas for its transport to the arc region. The diagram in Figure 1 shows the two processes with their differences and similarities.



Figure 1: Comparison of Plasma Transferred Arc processes and PAW

As mentioned above, the PTAW welding process and equipment are a modification of Gas Tungsten Arc Welding (GTAW). The significant difference involves a redesign of the GTAW torch to provide a concentration and collimation of the arc plasma. This is achieved by generating the arc and its plasma within the confines of the torch followed by discharging the high temperature ionized plasma through an orifice.

The diameter, configuration and throat length of the orifice are carefully designed to maximize the desirable properties of the arc, i.e. culmination, high temperature and stability. Orifice details are interchangeable so that variations in these dimensions are available to satisfy a variety of weld requirements. The orifice concentrates the plasma arc and collimates the flow so that it assumes a beam configuration as opposed to the "umbrella" shaped arc of the GTAW process.



Figure 2: Schematic view of Plasma Transferred Arc (PTA) Welding

Applications:

  • Hard Surfacing: PTAW is well suited to apply hard alloys for wear resistance. Stellite, Colmonoy, Hastelloy, and Tungsten Carbide can all be successfully applied with PTAW.
  • Corrosion Resistant Overlays: The localize heat input characteristics of PTAW allow corrosion resistant alloys to be applied with very little dilution into the base material. PTAW can achieve subsea chemistry requirements of <5% Fe in as little as 0.040” of overlay thickness.
  • Industries / Components:
    - Non-Mag Down Hole Tools: Drill Collars, Wear Bands for MWDs, Flex Ponies etc.
    - Down Hole Components: Mud Motor Bearings, Stabilizers, Topsubs, Piston SubsFlow Restrictors, Drill Bits etc.
    - Flow Control: Valve Bores, Gates, Seats, Seat Pockets, Ring Grooves, Valve Stems etc...
    - Power Generation: Turbine Blades, Shafts, Bearing Surfaces, etc.
    - Riser Equipment o Pins, Boxes, etc.


References

1. A.S.C.M.D’Oliviera, R.S.C.Paredes, R.L.C. Santos: Pulsed current plasma transferres arc hardfaccing, Journal of Materials Processing Technology 171, 2006, p.167–174;

2. V.V.Diaz, J.C.Dutra, A.S.C.D’Oliveira: Hardfacing by Plasma Transferred Arc Process, INTECH, Ed.W.Sudnik, 2011, ISBN 978-953-307-642-3;

3. P.V. Senthill, A.Shirrushti: Finite Element Simulation of Plasma Transferred Arc Welding [PTAW} of structural steel, PV Senthiil Int. Journal of Engineering Research and Applications www.ijera.com ISSN : 2248-9622, Vol. 4, Issue 10(Part - 4), October 2014, p.06-11;

4. What is Plasma Transferred Arc Welding [PTAW], 1/12/15, js, Accessed Oct 2015;

ナレッジベース検索

検索したい語句を入力:

検索方法

全文一致
キーワード

前方一致
要約

Total Materiaデータベースは世界の国々と広範な規格に関する数千種類の溶接に適した材料に関するデータを収録しております。

溶接に関する助言のほか必要に応じて、化学組成分、機械的特性、物理特性、炭素当量データなどの材料特性を御覧になれます。

高度な検索のページで材料グループのポップアップリストから’溶接フィラー材’を選び検索条件を決定します。さらに国/規格のフィールドを使い検索条件を絞ることもできます。

確定をクリックします。


選んだ材料の材料リストが表示されます。


結果リストで材料をクリックすると規格から導きだされるサブグループリストが表示されます。

そこから選んだ材料の特性を見る事ができさらにパワフルな相互参照表により類似材料、同等材料をみることもできます。


対象とする材料の特性データをクリックします。


Total Materiaデータベースをあなたにテスト評価を頂くために15万人以上の方が登録されている無料お試しコミュニティ-へ御招待致します。