AISI Designation system

概要:

The American Iron and Steel Institute has established a designation system for structural shapes, which has been adopted by steel producers. A four-numeral series is used to designate graduations of chemical composition of carbon steel. The first two digits indicate the grade of carbon steel. The last two numbers are intended to indicate the approximate middle of the carbon range. For example, in the grade designation 1035 represents a carbon range of 0.32% - 0.38%.

The American Iron and Steel Institute has established a designation system for structural shapes, which has been adopted by steel producers. A summary of the AISI designations is shown below.

"W" SHAPES are doubly-symmetric wide flange shapes used as beams or columns whose inside flange surfaces are substantially parallel. A shape having essentially the same nominal weight and dimensions as a "W" shape, but whose inside flange surfaces are not parallel, may also be considered a "W" shape, provided its average flange thickness is essentially the same shape as the flange thickness of the "W" shape.

"S" SHAPES are doubly-symmetric shapes produced in accordance with dimensional standards adopted in 1896 by the Association of American Steel Manufacturers for American Standard beam shapes. The essential part of these standards is that the inside flange surfaces of American Standard beam shapes have approximately a 16 2/3% slope.

"M" SHAPES are doubly-symmetric shapes that cannot be classified as "W", "S", or bearing pile shapes. Although not included in the standard nomenclature tabulation, bearing piles are doubly-symmetric wide flange shapes whose inside flange surfaces are essentially parallel and whose flange and web have essentially the same thickness.

"C" SHAPES are channels produced in accordance with dimensional Standards adopted in 1896 by the Association of American Steel Manufacturers for American Standard channels. The essential part of these standards is that the inside flange surfaces of American Standard channels have approximately a 16 2/3% slope.

"MC" SHAPES are channels that cannot be classified as "C"shapes.

DESIGNATION OF CARBON STEELS AISI/SAE

DEFINITION. Steel is considered to be carbon steel when no minimum content is specified or required for aluminum, chromium, cobalt, columbium, molybdenum, nickel, titanium, tungsten, vanadium, or zirconium, or any other element added to obtain a desired alloying effect; when the specified minimum for copper does not exceed 0.40%; or when the maximum content specified for any of the following elements does not exceed the percentages noted: manganese 1.65, silicon 0.60, copper 0.60.

NUMBERING SYSTEM. A four-numeral series is used to designate graduations of chemical composition of carbon steel. The first two digits( Table 1.) indicate the grade of carbon steel. The last two numbers are intended to indicate the approximate middle of the carbon range. For example, in the grade designation 1035 represents a carbon range of 0.32% - 0.38%.

It is necessary, however, to deviate from this system and to interpolate numbers in the case of some carbon ranges and for variations in manganese, phosphorus or sulfur within the same carbon range.

Within the numerical designation system the special-purpose elements lead and boron are commonly designated by inserting the letter "L" or "B" respectively between the second and third numerals of the AISI number, e.g., 10L45 and 10B46.

The prefix "M" indicates "merchant quality". The "M" grades are produced to wider carbon and manganese ranges than the corresponding standard grades which are not so prefixed.

Grade Description
10XX Non-resulfurized Carbon Steels, Manganese 1.00% maximum
11XX Resulfurized Carbon Steels
12XX Rephosphorized and Resulfurized Carbon Steels
15XX Non-resulfurized Carbon Steels, Manganese max. over 1.00%
*First two digits indicate grade of carbon steel.
**Last two digits represent middle of carbon range.

Table 1. Designation of carbon steels

ナレッジベース検索

検索したい語句を入力:

検索方法

全文一致
キーワード

前方一致
要約

Total Materiaデータベースで金属の規格、現在の状況、材料の定義内容を見るには一度クリックするだけで探せます。

Total Materia規格リストではで数秒以内に関連する材料特性詳細を探し同等材料の検索が可能になります。

まず、メニューバーの規格リストボタンをクリックします。


規格を選択するか規格番号を入力するだけで3万以上の規格が登録されている多言語データベースから直ちに結果を見る事が出来ます。

例えば、ポップアップからSAE規格を選ぶとその規格の金属材料全てを見る事ができます。


結果のリストは1600材料SAE金属材料規格より構成され、それらの情報としては: 規格の説明、最終発行年、現在の状況(有効か、入れ替えなど)で対応する規格により定義される材料のホットリンクを提供しております。


材料のホットリンクををクリックするだけで選ばれた規格により定義される材料のリストが表示されます。


このリストから特性の詳細、各々の材料の同等材料をが分かります。


Total Materiaデータベースをあなたにテスト評価を頂くために15万人以上の方が登録されている無料お試しコミュニティ-へ御招待致します。