High Manganese Austenitic Steels for Cryogenic Applications

Abstrakt:

Overall, a high manganese content significantly expands the austenite whereby high temperature ferrite formation is suppressed by the addition of Mn and will subsequently exhibit fully austenitic solidification from high temperature.
In high manganese steels it is possible to get significant improvements in the tensile ductility even at cryogenic temperatures as long as the number of ε-martensite plates is controlled.

As the name suggests, high-Mn steels are based on alloying Fe with a large amount of Mn (≥12 wt%). This makes the Fe-Mn equilibrium phase diagram an excellent starting point to understand their behavior. Figure 1 presents the equilibrium phase diagram of the Fe-Mn system. As can be seen, increasing Mn content significantly expands the austenite (γ) phase field. High temperature ferrite (δ) formation is suppressed by an addition of approximately 12-13 wt% Mn, indicating that alloys with this amount of manganese or more will exhibit fully austenitic solidification from high temperature. Another feature of interest in the Fe-Mn system is that the two phase region separating liquid (L) and austenite (γ) is quite narrow, suggesting that Mn does not segregate strongly during solidification. Estimating the partition ratio from the diagram itself gives a value of approximately 0.75. Although slightly outside of the data presented in Figure 1, a eutectoid reaction exists in the system at 255°C and 43 wt% Mn; γ→αFe+αMn. From a practical standpoint, the high-Mn alloys which are discussed here would not demonstrate any low temperature ferrite (αFe) formation during typical cooling conditions because of limited diffusion rates.



Figure 1: Fe-Mn equilibrium phase diagram

High manganese austenitic steels have been widely studied for their corresponding outstanding tensile strength and ductility. Certain high Mn austenitic steels have also been investigated for cryogenic applications. Koyama et al. studied the effects of temperature on the tensile properties of Fe-17Mn-0.6C steels and discovered that the uniform tensile elongation deteriorated as the deformation temperature decreased from room temperature to −100°C. The lower ductility was attributed to an increase in the amount of ε-martensite plates. This suggestion was supported by the observation that an addition of elements such as carbon, which suppressed the formation of ε-martensite, improved the cryogenic tensile ductility.

Therefore, it has been suggested that the reduction number of ε-martensite plates is a key factor for the cryogenic tensile ductility improvement of high Mn steels. One way for the number of ε-martensite plates to be suppressed is through austenite grain size refinement . Takaki et al. investigated the grain size effects on ε-martensite formation in Fe-15Mn alloys and discovered that when the grain size was below 10 µm, the ε-martensite transformation was almost suppressed. In a quite recent study, it was demonstrated that Fe-17Mn-0.6C alloys with coarse grain sizes (10–37 µm) demonstrated a brittle fracture at −150°C due to ε-martensite formation. In contrast, this embrittlement was suppressed by grain refinement to 3.5 µm. The formation of ε-martensite could also be suppressed by an increase in the Mn content. Tomota et al. demonstrated that, regarding the binary Fe-Mn system, when the Mn content was increased to 36%, no ε-martensite was observed in the tensile tested samples at room temperature, whereas only 4.2% of ε-martensite was formed following tensile deformation to a strain value exceeding 60% at the liquid nitrogen temperature. Fe-34.5Mn-0.04C steels are recently developed steels with potential applications at low temperatures.

Among 9% nickel steel, austenitic steel, aluminium alloy and austenitic Fe-Ni alloy that are materials applicable to LNG tanks, the three except for 9% nickel steel have a FCC crystal structure. Metallic materials with FCC structure do not show the property of ductile-brittle transition unlike those with common Body-Centered Cubic (BCC) structure. Thus, they maintain high toughness also at cryogenic temperatures. An exception is the 9% nickel steel, which has the residual FCC structure with a basis of Body-Centered Tetragonal (BCT) structure due to a special heating process that ensures toughness at cryogenic temperatures.

Alloy steel with FCC crystal structure is referred to as austenitic steel. Types of austenitic steel are nickel-based austenitic stainless steel such as types 304, 304L, 316, 316L, 321 and 347. Since the 1970s, comprehensive studies on austenitic steel for cryogenic applications based on manganese have been actively carried out. Recently, high manganese austenitic steel for cryogenic service (hereinafter referred to as “high Mn steel”) has been developed as an alternative that overcomes the disadvantage of FCC-structured metallic materials, namely low yield strength, and leverages the economic feasibility of manganese. Chemical composition of high Mn steel is registered in Korean industrial standards (KS-D-3031) as follows:



Table 1: Chemical compositions of high Mn steel (wt%)

Mechanical properties of high Mn steel were tested in accordance with international standard procedures as seen in Table 2. They were clarified through a comparison with other materials used for LNG tanks shown in Table 3. Particularly, Type 304 was chosen to represent austenitic stainless steel.



Table 2: Mechanical test items for high Mn steel



Table 3: Specifications of 5 different cryogenic materials

In Figure 1(a) is showed, yield strength of high Mn steel. As can be seen the yield stress is between those of Type 304 (equivalent to STS 304 in Korean Standards) and 9% nickel steel. In terms of ultimate tensile strength, it shows superiority over every type of metallic material in comparison. High Mn Steel recorded an elongation of around 80% of that of Type 304 and around 1.8-fold of that of 9% nickel steel. (a) Comparison with other cryogenic (b) Variation with respect to temperature Materials (25°C) Figure 1(b) shows the yield strength and ultimate tensile strength of high Mn steel increase monotonically and its elongation decreases, as test temperature decreases.



Figure 2: Stress-Strain curves of high Mn steel - (a) Comparison with other cryogenic materials (25°C) (b) Variation with respect to temperature


References

1. B. James Sutton: Solidification Behavior and Hot Cracking Susceptibility of High Manganese Steel Weld Metals, The Ohio State University, 2013;

2. Y. Wang, B. Shi, Y. He, H. Zhang, Y. Peng, T. Wang: A Fine Grain, High Mn Steel with Excellent Cryogenic Temperature Properties and Corresponding Constitutive Behaviour, Materials 2018, 11, 253; doi:10.3390/ma11020253;

3. Suitability of High manganese austenitic steel for cryogenic service and development of any necessary amendments to the IGC code and IGF code, CCC 3 8 Technical information regarding high manganese austenitic steel for cryogenic service, 2016, Accessed NOV 2018.

Durchforschen Sie bitte den Informationsteil der Datenbank

Geben Sie bitte eine Anfrage, um Suche einzuleiten:

Suche nach

Vollständiger Text
Schlüsselwörter

Überschriften
Abstracts

Wärmebehandlungsdiagramme stenen, in der Total Materia Datenbank, für eine grosse Anzahl von Werkstoffen zur Verfügung.

Wärmebehandlungsdiagramme die Härtbarkeit, Härte-Anlasstemperatur-Kurven, TTT und CCT umfassen, können in den meisten Standard Datasets gefunden werden.

Um Werkstoffe über spezielle Eigenschaften auszuwählen, können Sie die Spezialsuche benutzen, indem Sie im Modul der erweiterten Suche die entsprechenden Felder abhaken.

Um Ihre Suchkriterien zu definieren, brauchen Sie nur das entsprechende Land/Norm aus der Liste auszuwählen und das Feld "Wärmebehandlungsdiagramme" der Spezialsuche ankreuzen, welches sich im unteren Teil der Seite der erweiterten Suche befindet.

Klicken Sie auf "Absenden".


Nachdem Sie den Werkstoff ausgesucht haben der Sie interessiert, klicken Sie auf den Link der Wärmebehandlung um die Daten für den ausgewählten Werkstoff zu sehen. Die Anzahl der zur Verfügung stehenden Daten zur Wärmebehandlung ist neben dem Link, in Klammern, angegeben.


Alle zur Verfügung stehende Information über die Wärmebehandlung wird dann angezeigt.






Um unsere Datenbank auszuprobieren, laden wir Sie ein sich unserer Nutzergemeinschaft von über 150 000 angemeldeten Benutzern, mit einem kostenlosen Probeaboanzuschliessen.