无碳化物贝氏体钢 (CFB):第二部分
双辊铸轧镁合金的机械性能
选择性激光烧结 (SLS):第二部分
DataPLUS 模块提供上万种金属材料和非金属材料的腐蚀数据、焊接性能、尺寸与公差信息以及涂层信息。 点击这里了解更多。
Total Materia New Application Launch! 2021年1月14日
Total Materia New Application Launch! 2021年2月10日
Total Materia New Application Launch! 2021年3月10日
在使用Total Materia几个月之后,以及深刻体验过所有潜在功能之后,我非常感谢你们的卓越工作和持续稳定的升级服务。 Total Materia始终是用来达成这一目的唯一工具。
M. Manfredini Bonfiglioli Industrial Gearmotors 博洛尼亚, 意大利
我们的目标很简单,就是让 Total Materia成为全球工程师在材料领域的首选一站式解决方案
Prof. Dr. Viktor Pocajt, CEOKey to Metals AG
Tensile test is the most widely used test to determine the mechanical properties of materials. In this test, a piece of material is pulled until it fractures. Strain and stress are calculated from these values, and are used to construct a stress-strain curve. From this curve, the elastic modulus and yield strength are determined.
The tensile test is the most widely used test to determine the mechanical properties of materials. In this test, a piece of material is pulled until it fractures. During the test, the specimen elongation and applied load is measured. Strain and stress are calculated from these values, and are used to construct a stress-strain curve. From this curve, the elastic modulus and yield strength are determined.
The highest load in the tensile test gives the tensile or ultimate strength. After fracture, the final length and cross-sectional area of the specimen are used to calculate the percent elongation and percent reduction of area, respectively. These quantities indicate the ductility of the material. By using the instantaneous length and cross-sectional area, the true stress and true plastic strain are calculated from the load and elongation.
The strain hardening properties of the material are then determined from a log-log plot of the true stress vs. the true plastic strain. Thus, from one test a large amount of information can be obtained about the mechanical properties of a material.
Numerous groups have developed standard methods for conducting the tensile test. In the United States, standards published by ASTM are commonly used to define tensile-test procedures and parameters. Standard Methods for conducting the tensile test are also available from other standards organizations, such as the Japanese Industrial Standards (JIS), the Deutsche Institut für Normung (DIN), and the International Organization for Standardization (ISO). Other domestic technical groups in the United States have developed standards, but in general, these are based on ASTM E.8.
Typical test pieces are shown below. They are normally circular, but may be flat. The standard diameter is 12.5mm.
The tensile test piece is mounted into the grips of the tensile test machine. The grips are moved apart at a constant rate and the applied load is measured by a load cell while the extension is measured by an extensometer.
The test is normally destructive - the test piece is permanently deformed and usually fractured in the test.
This Japanese Industrial Standard specifies test pieces for tensile test for metallic materials (hereafter referred to as “test piece”). The type of test piece depends upon the form and size and these are generally classified into the proportional test piece and the non-proportional piece as described in Table 1.
The selection of the type of test piece to be used shall be in accordance with the requirements of the standard for that particular material, but it is recommended to be selected as given in Table 2.
*t - thicknesses in mm **D - outside diameter in mm
Remarks: 1. N°1B test piece shall be used in the case where the test pieces shown in Table 2 are not suitable to be used. 2. N°3, N°6 and N°7 test piece specified in Annex should be used when the use of test pieces given in Table 2 is not suitable. 3. For the materials specified in the International Standard, the division of use shown in the following remarks Table 1 may be used.
***A- sectional area of parallel portion
Date Published: Aug-2011
输入搜索词:
搜索项
全文 关键字
标题 摘要
The Total Materia Extended Range includes a unique collection of stress-strain curves and diagrams for calculations in the plastic range for thousands of metal alloys, heat treatments and working temperatures. Both true and engineering stress curves are given for various strain rates where applicable.
Finding a stress-strain graph in the database is simple and takes only seconds.
Enter the material of interest into the quick search field. You can optionally narrow your search by specifying the country/standard of choice in the designated field and click Search.
After selecting the material of interest to you, click on the Stress-Strain diagrams link to view data for the selected material. The number of available stress-strain diagrams is displayed in brackets next to the link.
Because Total Materia stress-strain curves are neutral across standard specifications, you can review stress-strain diagrams by clicking the appropriate link for any of the subgroups.
Besides the stress-strain curves at different temperatures, stress and strain data are given in a tabular format which is convenient for copying to, for example, a CAE software.
It is also possible to view stress-strain curves and data for other working temperatures.
To do this, simply insert a new temperature into the ‘Enter temperature’ field within the defined range.
After clicking the Calculate button, a new curve is plotted and values in the table now correspond to the temperature you have defined. See example below for 250°C.
For you’re a chance to take a test drive of the Total Materia database, we invite you to join a community of over 150,000 registered users through the Total Materia Free Demo.