Copper Beryllium Alloys


The addition of beryllium in copper alloy materials gives a substantial increase in strength without resulting in brittle behavior.
Due to these improved properties, beryllium alloys are used widely in the aviation industries in components which require high strength and a high tolerance to wear.

Beryllium metal is used in a variety of alloys including the alloy, copper beryllium. Beryllium-copper alloys are amongst the strongest of the copper alloys. They are commonly used at cryogenic temperatures where, like other copper alloys, they do not become brittle. They can be machined relatively easily, and are readily joined by soft soldering or brazing. Handling and most machining operations concerning beryllium-copper alloys are considered non-hazardous.

In the aviation industry copper beryllium has been used in a variety of components due to its strength and tolerance to wear and its’ electricity conductivity (e.g. high load and stress bushes on aircraft under carriage and propeller electrical contact slip rings).

Figure 1: Equilibrium diagram of copper-beryllium alloys

The literature contains many additional references on the properties of copper-beryllium alloys. Most of these, however, pertain to the response of copper-beryllium alloys to precipitation heat treatment, to their forming characteristics, and to their use for specific applications with little or no data that can be used for general engineering design.

There are two classes of copper beryllium alloys: High Strength Copper Beryllium has the highest strength of any copper alloy, and offers good thermal and electrical conductivity’s. Depending on the product form, the tensile strength can exceed 200,000 psi (140 kg/mm2), with an electrical conductivity in the range of 18-25% IACS, and a thermal conductivity of 60 BTU/ft·hr·°F (105 W/m·K). The high conductivity of copper beryllium alloys offers considerably better conductivity’s (50-60% IACS and 145 BTU/ft·hr·°F, 250 W/m·K) at a moderate strength level of about 120,000 psi (85 kg/mm2).

The high conductivity copper beryllium alloys are diamagnetic and have magnetic behavior similar to metallic copper. The high strength alloys, typical of most copper alloys, are weakly paramagnetic. Table 1 lists copper beryllium’s typical magnetic properties as determined by the Gouy balance and vibrating sample magnetometry techniques.

Table 1: Magnetic Properties (cgs units at 1000 Gauss) of Copper Beryllium

Copper beryllium’s magnetic properties are constant over the entire strength range of the alloys. The magnetic properties are not temperature dependent from liquid helium to above room temperature. Figure 2 shows that magnetic field strength has a minor influence on the magnetic properties of copper beryllium.

Figure 2: Effect of field strength on the magnetic susceptibility (volume) of Copper Beryllium

Cold work or plastic deformation does not change the magnetic performance of copper beryllium. As a result of cold work, which may occur in service, some nonmagnetic austenitic stainless steels transform to ferromagnetic martensite. As shown in Figure 3, deformation increases the susceptibility of the stainless steel while it has no effect on copper beryllium. The localized deformation from machining or surface abuse can result in magnetic hot spots in stainless steel. The martensitic transformation in stainless steels occurs more readily at low temperatures. Accumulated strains, resulting from thermal cycling to low temperature, can cause a deterioration in nonmagnetic quality in stainless steel. This is not a problem with copper beryllium.

Figure 3: Effect of deformation on magnetic susceptibility of Copper Beryllium and Stainless Steel

기술 자료 검색

검색할 어구를 입력하십시오:

검색 범위



Total Materia는 다양한 나라와 규격에 따른 수천개의 구리 재질에 대한 정보를 포함하고 있습니다.

재질의 화학적 조성, 기계적 특성, 물리적 특성, 고급 물성 데이터 등의 전체적인 특성 정보들을 어디서든 검토하실 수 있습니다.

고급 검색을 이용하여, 검색 조건의 재질 리스트에서 '구리'를 선택합니다. 검색 범위 좀 더 줄이기를 원하신다면 국가/규격과 같은 다른 조건을 지정할 수 있습니다.

검색 버튼을 클릭합니다.

선택된 정보에 부합하는 일련의 재질이 검색됩니다.

결과 리스트에서 재질을 선택하시면, 일련의 규격 사양 소그룹이 나타납니다.

여기에서 선택한 재질의 특정 특성 데이터를 검토하실 수도 있고, 강력한 상호 참조 표를 이용하여 유사 재질이나 등가 재질을 검토하는 것 또한 가능합니다.

자세한 특성 데이터를 보시려면 특성 데이터 링크를 클릭하세요.

Total Materia 데이터베이스를 사용해 보실 수 있는 기회가 있습니다. 저희는 Total Materia 무료 체험을 통해 150,000명 이상의 사용자가 이용하고 있는 커뮤니티로 귀하를 초대합니다.