Fatigue of Nickel-Based Superalloys: Part One


A critical property of nickel-based superalloys is their resistance to fatigue-crack propagation, particularly at service temperatures.
Many nickel-based superalloys are subject to formation of cracks or incipient cracks, either in fabrication or in use, and that the cracks can actually propagate or grow while under stress during the use in structures such as gas turbines and jet engines.

Nickel-based superalloys are widely used in turbines for both aerospace and land-based power-generation applications, due to their exceptional elevated-temperature strength, high resistance to creep, oxidation, and corrosion, and good fracture toughness. However, a critical property of these alloys is their resistance to fatigue-crack propagation, particularly at service temperatures.

In engine applications, there are often two components to this problem:

  • low-cycle fatigue, which results from relatively large cycles associated with the stopping and starting of the turbine, and
  • high-cycle fatigue (HCF), associated with vibrational loading during service.

Fatigue results in rapid, and often unpredictable, failures due to the propagation of fatigue cracks in blade and disk components under high-frequency loading, where the cracking initiates from small defects, in many instances resulting from fretting or foreign-object damage. Due to the high vibrational frequencies involved, even cracks growing at slow per-cycle velocities can propagate to failure in short time periods, possibly within a single flight segment. Consequently, HCF-critical turbine-engine components must be operated below the fatigue-crack initiation or growth thresholds, such that cracking cannot occur within ~109 cycles.

Nickel-based superalloys have been used extensively in jet engines, in land based gas turbines and other machinery where they must retain high strength and other desirable physical properties at elevated temperatures of 1000°F (540°C) or more. Many of these alloys contain a γ' precipitate in varying volume percentages. The γ' precipitate contributes to the high performance properties of such alloys at their elevated use temperatures.

A problem which has been recognized to a greater and greater degree with many nickel-based superalloys is that they are subject to formation of cracks or incipient cracks, either in fabrication or in use, and that the cracks can actually propagate or grow while under stress as during use of the alloys in such structures as gas turbines and jet engines. The propagation or enlargement of cracks can lead to part fracture or other failure and the consequences of failures of the moving mechanical part due to crack formation and propagation can be particularly hazardous.

A principal finding of a NASA sponsored study was that the rate of propagation based on fatigue phenomena or in other words, the rate of fatigue crack propagation (FCP), was not uniform for all stresses applied nor to all manners of applications of stress. More importantly, the finding was that fatigue crack propagation actually varied with the frequency of the application of stress to the part where the stress was applied in a manner to enlarge the crack.

More surprising still was the magnitude of the finding from the NASA sponsored study that the application of stress of lower frequencies rather than at the higher frequencies previously employed in studies, actually increased the rate of crack propagation. In other words the NASA study verified that there was a time dependence in fatigue crack propagation. Further, the time dependence of fatigue crack propagation was found to depend not on frequency alone but on the time during which the member was held under stress, so-called hold-time.

To date, the grain-boundary engineering approach has been shown to be particularly successful in promoting fracture resistance in specific cases, notably in the context of intergranular stress-corrosion cracking and creep. However, its effect on the fatigue resistance has largely been unexplored.

According to one study, ambient temperature, smooth-bar, tension-tension fatigue lives for two γ / γ' superalloys were reported to be increased by a factor of ~1.5 in an Fe-based alloy by increasing the fraction of special boundaries from 20 to 65 pct and by a factor of 3 in a Ni-based alloy by increasing this fraction from 9 to 49 pct, although no mechanistic explanation was presented.

Clearly, the effectiveness of grain-boundary engineering will depend upon the nature of the crack path, specifically, the preponderance of intergranular versus transgranular cracking. In light of this, the objectives of the studies was to investigate, the feasibility of using grain boundary engineering processing to promote resistance to fatigue-crack propagation, particularly at near-threshold levels, in a new polycrystalline nickel-based disk alloy, ME3 (Ni-Co-Cr Alloy). Specifically, the crack growth rates and threshold behavior of large (8 to 20 mm) through-thickness cracks were examined over a range of temperatures (25°C, 700°C, and 800°C) in order to enhance the incidence of intergranular crack growth, Figure 1.

Figure 1: Variation in fatigue-crack propagation behavior for small surface cracks in the grain-coarsened ME3, together with EBSD characterization of the path for small crack propagation. Random boundaries are shown as black lines twin boundaries are in red, other special boundaries are in yellow.

Etsi tietämyskannasta

Kirjoita etsittävä lauseke:


Koko teksti


Tämä artikkeli kuuluu artikkelisarjaan. Voit klikata alla olevia linkkejä lukeaksesi lisää aiheesta.

Total Materia Extended Range includes the largest database of fatigue data and cyclic properties for thousands of metal alloys, heat treatments and loading conditions. Both strain life and stress life parameters are given, with monotonic properties added for the reference, and statistical parameters and estimates where applicable.

Finding cyclic properties in the database is very easy and takes only seconds.

Enter the material of interest into the quick search field. You can optionally narrow your search by specifying the country/standard of choice in the designated field and click Search.

solution img

After selecting the material of interest to you, click on the Fatigue data link to view data for the selected material. The number of available fatigue data sets is displayed in brackets next to the link.

solution img

Because Total Materia Extended Range cyclic properties are neutral to standard specifications, you can review fatigue data by clicking the appropriate link for any of the subgroups. Strain life and stress life data are given in a tabular format, with graphs where applicable.

solution img

Explicit references to the data sources are given for each dataset. Please see example below.

solution img

For you’re a chance to take a test drive of the Total Materia database, we invite you to join a community of over 150,000 registered users through the Total Materia Free Demo.