High Strength Low Alloy V Steels: Part One

Abstract:

High-strength low-alloy (HSLA) steels, or microalloyed steels, are designed to provide better mechanical properties and/or greater resistance to atmospheric corrosion than conventional carbon steels.
Vanadium contributes to strengthening by forming fine precipitate particles (5 to 100 nm in diameter) of V(CN) in ferrite during cooling after hot rolling.

Low alloy steel is one of the most rapidly developed and highly utilized steel grades in recent years and has become the most produced, applied and economic steel available. The stipulated minimum yield strength is 275 MPa with a maximum value of 1035 MPa. A category of steel with these characteristics is made by adding a small proportion of alloy element in the carbon steel, which will ensure the steel has high strength, good toughness, high weldability and strong formality and erosion resistance under hot rolling or heat treatment conditions.

Normal elements for alloyment are generally strong carbide combination elements such as Ti, Nb and V. Nb are most widely applied and are the subject of most research projects due to the fact that it can effectively condition various physical metallurgy factors and have the biggest refinement and precipitation strengthening in traditional controlled rolling process. However, there has never been an equal determination to study the research and development of Ti-alloyed and V-alloyed microstructural steels.

High-strength low-alloy (HSLA) steels, or microalloyed steels, are designed to provide better mechanical properties and/or greater resistance to atmospheric corrosion than conventional carbon steels. They are not considered to be alloy steels in the normal sense because they are designed to meet specific mechanical properties rather than a chemical composition (HSLA steels have yield strengths greater than 275 MPa, or 40 ksi). The chemical composition of a specific HSLA steel may vary for different product thicknesses to meet mechanical property requirements.

The HSLA steels in sheet or plate form have low carbon content (0.05 to −0.25% C) in order to produce adequate formability and weldability, and they have manganese content up to 2.0%. Small quantities of chromium, nickel, molybdenum, copper, nitrogen, vanadium, niobium, titanium, and zirconium are used in various combinations.

Niobium and vanadium, the most frequently used micro alloy additives, are added to achieve similar objectives-to condition the austenite and to precipitate at various stages of processing. These two elements are not interchangeable however, and for optimum results, specific steel chemistry and processing parameters are required.

  Vanadium Niobium
Solubility of M (C,N) in austenite High Low
Propensity for Concast Cracking Low High
Ease of recrystalization High Low
Compatibility with Nitrogen Positive Negative
N effect on Precipitation in austenite Limited Intensive
N effect on Precipitation in ferrite Positive Absent
Nitrogen Binding Capacity Strong Minor

Table 1: Critical size of macro inclusions in cast semis that cause process upsets and product defects

High strength low alloy (HSLA) steels offer the advantage of weight and cost savings compared to mild steel. Therefore they are widely used in the automotive and the construction industry.

Vanadium Microalloyed Steels

The development of vanadium containing steels occurred shortly after the development of weathering steels, and flat-rolled products. With up to 0.10% V these materials are widely used in a hot-rolled condition. Vanadium-containing steels are also used in the controlled-rolled, normalized, or quenched and tempered condition.

Vanadium contributes to strengthening by forming fine precipitate particles (5 to 100 nm in diameter) of V(CN) in ferrite during cooling after hot rolling. These vanadium precipitates, which are not as stable as niobium precipitates, are in solution at all normal rolling temperatures and thus are very dependent on the cooling rate for their formation. Niobium precipitates, however, are stable at higher temperatures, which is beneficial for achieving fine-grain ferrite.

The austenite grain size of hot-rolled steels is determined by the recrystallization and grain growth of austenite during rolling. Vanadium hot-rolled steels usually undergo conventional rolling but are also produced by recrystallization controlled rolling. With conventional rolling, vanadium steels provide moderate precipitation strengthening and relatively little strengthening from grain refinement. The maximum yield strength of conventionally hot-rolled vanadium steels with 0.25% C and 0.08% V is about 450 MPa (65 ksi). The practical limit of yield strengths for hot-rolled vanadium-microalloyed steel is about 415 MPa (60 ksi), even when controlled rolling techniques are used.

Vanadium steels subjected to recrystallization controlled rolling require a titanium addition so that a fine precipitate of TiN is formed that restricts austenite grain growth after recrystallization. Yield strengths from conventional controlled rolling are limited to a practical limit of about 415 MPa (60 ksi) because of the lack of retardation of recrystallization. When both strength and impact toughness are important factors, controlled-rolled low-carbon niobium steel (such as X-60 hydrogen-induced cracking resistant plate) is preferable.

Search Knowledge Base

Enter a phrase to search for:

Search by

Full text
Keywords

Headings
Abstracts

This article belongs to a series of articles. You can click the links below to read more on this topic.

Finding chemical composition data in the Total Materia database couldn’t be easier.

Within seconds it is possible for you to find useful chemical composition data for over 175,000 materials in the database.

Enter the material of interest into the quick search field. You can optionally narrow your search by specifying the country/standard of choice in the designated field and click Search.

solution img

Total Materia will generate the search list for you to select the material of interest from the material list.
Click on the material of interest.

solution img

On the subgroup page, click the composition link to view chemical composition data for the selected material. The number of chemical composition data records is displayed in brackets next to the link.

solution img

The chemical composition data will be then be displayed along with all selected material information for your reference.

solution img

For you’re a chance to take a test drive of the Total Materia database, we invite you to join a community of over 150,000 registered users through the Total Materia Free Demo.