PROPRIETARY Micro-Melt M48 Alloy Acier pour outils
Mises à jour des données
Ce matériau a 19 entrées de propriétés – seul un aperçu est visible ici.
Déverrouillez l’accès aux propriétés détaillées du matériau, notamment en température et dans différentes conditions.
Inscription gratuite requise • Accès instantané
PROPRIETARY Micro-Melt M48 Alloy Composition chimique
Carpenter Technology Corporation, Product Data Sheets,
Vous souhaitez voir toutes les données sur ce matériau ?
Inscription gratuite requise • Accès instantané
PROPRIETARY Micro-Melt M48 Alloy Propriétés physiques
Température
Ce matériau a 19 entrées de propriétés – seul un aperçu est visible ici.
Déverrouiller l’accès aux propriétés physiques à différentes températures et conditions.
Inscription gratuite requise • Accès instantané
PROPRIETARY Micro-Melt M48 Alloy Traitement thermique
- Annealing: heat uniformly to 871°C (1600°F), hold at temperature for two hours, cool slowly at 14°C (25°F) per hour maximum in the furnace to below 538°C (1000°F), and air cool to room temperature.
Hardening: it is customary to use two furnaces to harden Micro-Melt M48 alloy. One furnace is used to preheat the workpiece to 816/843°C (1500/1550°F), and the second is used to rapidly heat the workpiece from the preheating temperature to the hardening temperature of 1149/1204°C (2100/2200°F). Typical soak times are 2-3 minutes at the high temperature.
Quenching: quench in oil or a salt bath maintained at 538/593°C (1000/1100°F). The workpiece should be quenched in oil until it has reached approximately 538/593°C (1000/1100°F) (dull red color), removed from the oil and allowed to air cool to below 66°C (150°F), or until the work-piece can be touched comfortably with a bare hand. When a salt bath is used, the workpiece is quenched into the bath and held long enough to cool to the bath temperature. It is then removed from the bath and allowed to air cool to below 66°C (150°F), or until it can be touched comfortably with a bare hand.
Straightening: any necessary straightening should be done from the quench at any temperature down to 427°C (800°F).
Stress Relieving: heat slowly to 621/677°C (1150/1250°F), hold 1 to 2 hours, then cool in still air.
Tempering: tempering should be performed immediately after quenching and cooling of the workpiece below 66°C (150°F), or as soon as it can be touched comfortably with a bare hand. Typical tempering is performed at 538°C (1000°F) for two hours at temperature followed by air cooling to room temperature. This cycle is repeated twice to obtain triple tempering.
PROPRIETARY Micro-Melt M48 Alloy Matériaux équivalents internationaux
Affichage de 2 sur 3 résultats.
Les catégories d'équivalence reflètent une comparaison de la composition chimique et des propriétés mécaniques — vérifiez toujours l'adéquation par rapport à la spécification applicable à votre utilisation.
Besoin de la liste complète des 3 équivalents internationaux ?
Consultez les 3 nuances équivalentes avec une correspondance détaillée par norme, producteur et catégorie d'équivalence.
Inscription gratuite requise • Accès instantané
Optimisez les choix de matériaux pour votre application - Réserver une démo
- 3Références croisées
- 8Composition
- -Propriétés mécaniques
- 5Propriétés physiques
- 1Traitement thermique
- -Métallographie
- -Usinabilité
- -Contrainte-Déformation
- -Formabilité
- -Fatigue
- -Rupture
- -Rampant
- -Assemblages
- -Revêtements
- -Dimensions
- -Tribologie
- -Corrosion
- -Vieillissement
- -Résistance aux intempéries
- -Irradiation
- 2Fournisseurs totaux