PROPRIETARY Micro-Melt M48 Alloy Acciai per utensili
Aggiornamenti dei dati
Questo materiale dispone di 19 dati sulle proprietà — qui ne viene mostrato solo un sottoinsieme.
Sblocca tutte le proprietà del materiale, inclusi i valori dettagliati a diverse temperature e condizioni.
Registrazione gratuita richiesta • Accesso immediato
PROPRIETARY Micro-Melt M48 Alloy Composizione chimica
Carpenter Technology Corporation, Product Data Sheets,
Cerchi dati completi sulle prestazioni dei materiali?
Registrazione gratuita richiesta • Accesso immediato
PROPRIETARY Micro-Melt M48 Alloy Proprietà fisiche
Temperatura
Questo materiale dispone di 19 dati sulle proprietà — qui ne viene mostrato solo un sottoinsieme.
Sblocca valori fisici dettagliati a diverse temperature e condizioni.
Registrazione gratuita richiesta • Accesso immediato
PROPRIETARY Micro-Melt M48 Alloy Trattamento Termico
- Annealing: heat uniformly to 871°C (1600°F), hold at temperature for two hours, cool slowly at 14°C (25°F) per hour maximum in the furnace to below 538°C (1000°F), and air cool to room temperature.
Hardening: it is customary to use two furnaces to harden Micro-Melt M48 alloy. One furnace is used to preheat the workpiece to 816/843°C (1500/1550°F), and the second is used to rapidly heat the workpiece from the preheating temperature to the hardening temperature of 1149/1204°C (2100/2200°F). Typical soak times are 2-3 minutes at the high temperature.
Quenching: quench in oil or a salt bath maintained at 538/593°C (1000/1100°F). The workpiece should be quenched in oil until it has reached approximately 538/593°C (1000/1100°F) (dull red color), removed from the oil and allowed to air cool to below 66°C (150°F), or until the work-piece can be touched comfortably with a bare hand. When a salt bath is used, the workpiece is quenched into the bath and held long enough to cool to the bath temperature. It is then removed from the bath and allowed to air cool to below 66°C (150°F), or until it can be touched comfortably with a bare hand.
Straightening: any necessary straightening should be done from the quench at any temperature down to 427°C (800°F).
Stress Relieving: heat slowly to 621/677°C (1150/1250°F), hold 1 to 2 hours, then cool in still air.
Tempering: tempering should be performed immediately after quenching and cooling of the workpiece below 66°C (150°F), or as soon as it can be touched comfortably with a bare hand. Typical tempering is performed at 538°C (1000°F) for two hours at temperature followed by air cooling to room temperature. This cycle is repeated twice to obtain triple tempering.
Materiali equivalenti internazionali di PROPRIETARY Micro-Melt M48 Alloy
Visualizzazione di 2 risultati su 3.
Le categorie di equivalenza si basano sul confronto della composizione chimica e delle proprietà meccaniche. Si raccomanda di verificare sempre l'idoneità del materiale rispetto alla specifica e all'applicazione prevista.
Hai bisogno dell'elenco completo dei 3 equivalenti internazionali?
Visualizza tutti i 3 gradi equivalenti con una mappatura dettagliata per norma, produttore e categoria di equivalenza.
Registrazione gratuita richiesta • Accesso immediato
Ottimizza la selezione dei materiali per la tua applicazione - Prenota una demo
- 3Riferimenti incrociati
- 8Composizione
- -Proprietà meccaniche
- 5Proprietà fisiche
- 1Trattamento Termico
- -Metallografia
- -Lavorabilità
- -Sforzo-Deformazione
- -Formabilità
- -Fatica
- -Frattura
- -Strisciare
- -Giunzioni
- -Rivestimenti
- -Dimensioni
- -Tribologia
- -Corrosione
- -Invecchiamento
- -Resistenza agli agenti atmosferici
- -Irraggiamento
- 2Fornitori Totali