PROPRIETARY Micro-Melt M48 Alloy Aceros para herramientas
Actualizaciones de datos
Este material cuenta con 19 propiedades — aquí solo se muestra una parte.
Accede a todas las propiedades del material, incluyendo valores detallados según temperatura y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY Micro-Melt M48 Alloy Composición química
Carpenter Technology Corporation, Product Data Sheets,
¿Buscas datos completos de desempeño de materiales?
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY Micro-Melt M48 Alloy Propiedades físicas
Temperatura
Este material cuenta con 19 propiedades — aquí solo se muestra una parte.
Consulta propiedades físicas detalladas en distintas temperaturas y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY Micro-Melt M48 Alloy Tratamiento Térmico
- Annealing: heat uniformly to 871°C (1600°F), hold at temperature for two hours, cool slowly at 14°C (25°F) per hour maximum in the furnace to below 538°C (1000°F), and air cool to room temperature.
Hardening: it is customary to use two furnaces to harden Micro-Melt M48 alloy. One furnace is used to preheat the workpiece to 816/843°C (1500/1550°F), and the second is used to rapidly heat the workpiece from the preheating temperature to the hardening temperature of 1149/1204°C (2100/2200°F). Typical soak times are 2-3 minutes at the high temperature.
Quenching: quench in oil or a salt bath maintained at 538/593°C (1000/1100°F). The workpiece should be quenched in oil until it has reached approximately 538/593°C (1000/1100°F) (dull red color), removed from the oil and allowed to air cool to below 66°C (150°F), or until the work-piece can be touched comfortably with a bare hand. When a salt bath is used, the workpiece is quenched into the bath and held long enough to cool to the bath temperature. It is then removed from the bath and allowed to air cool to below 66°C (150°F), or until it can be touched comfortably with a bare hand.
Straightening: any necessary straightening should be done from the quench at any temperature down to 427°C (800°F).
Stress Relieving: heat slowly to 621/677°C (1150/1250°F), hold 1 to 2 hours, then cool in still air.
Tempering: tempering should be performed immediately after quenching and cooling of the workpiece below 66°C (150°F), or as soon as it can be touched comfortably with a bare hand. Typical tempering is performed at 538°C (1000°F) for two hours at temperature followed by air cooling to room temperature. This cycle is repeated twice to obtain triple tempering.
PROPRIETARY Micro-Melt M48 Alloy Materiales Internacionales Equivalentes
Mostrando 2 de 3 resultados.
Las categorías de equivalencia reflejan comparaciones de composición química y propiedades mecánicas; siempre verifique la idoneidad del material según la especificación aplicable a su aplicación.
¿Necesita la lista completa de los 3 internacionales equivalentes?
Consulte los grados 3 equivalentes con el detalle completo de correspondencias por norma, fabricante y categoría de equivalencia.
Se requiere registro gratuito • Acceso inmediato
Optimiza la selección de materiales para tu aplicación - Reservar una demo
- 3Referencias cruzadas
- 8Composición
- -Propiedades mecánicas
- 5Propiedades físicas
- 1Tratamiento térmico
- -Metalografía
- -Maquinabilidad
- -Esfuerzo-Deformación
- -Conformabilidad
- -Fatiga
- -Fractura
- -Bicho raro
- -Uniones
- -Revestimientos
- -Dimensiones
- -Tribología
- -Corrosión
- -Envejecimiento
- -Resistencia a la intemperie
- -Irradiación
- 2Proveedores Totales