PROPRIETARY Micro-Melt M48 Alloy Werkzeugstähle
Datenaktualisierungen
Dieser Werkstoff verfügt über 19 Eigenschaften – hier wird nur ein Teil davon angezeigt.
Erhalten Sie Zugriff auf alle Werkstoffeigenschaften, einschließlich detaillierter Werte für verschiedene Temperaturen und Zustände.
Kostenlose Registrierung erforderlich • Sofortiger Zugriff
PROPRIETARY Micro-Melt M48 Alloy Chemische Zusammensetzung
Carpenter Technology Corporation, Product Data Sheets,
Suchen Sie nach vollständigen Daten für Werkstoffe?
Kostenlose Registrierung erforderlich • Sofortiger Zugriff
PROPRIETARY Micro-Melt M48 Alloy Physikalische Eigenschaften
Temperatur
Dieser Werkstoff verfügt über 19 Eigenschaften – hier wird nur ein Teil davon angezeigt.
Erhalten Sie detaillierte physikalische Werte für verschiedene Temperaturen und Bedingungen.
Kostenlose Registrierung erforderlich • Sofortiger Zugriff
PROPRIETARY Micro-Melt M48 Alloy Wärmebehandlung
- Annealing: heat uniformly to 871°C (1600°F), hold at temperature for two hours, cool slowly at 14°C (25°F) per hour maximum in the furnace to below 538°C (1000°F), and air cool to room temperature.
Hardening: it is customary to use two furnaces to harden Micro-Melt M48 alloy. One furnace is used to preheat the workpiece to 816/843°C (1500/1550°F), and the second is used to rapidly heat the workpiece from the preheating temperature to the hardening temperature of 1149/1204°C (2100/2200°F). Typical soak times are 2-3 minutes at the high temperature.
Quenching: quench in oil or a salt bath maintained at 538/593°C (1000/1100°F). The workpiece should be quenched in oil until it has reached approximately 538/593°C (1000/1100°F) (dull red color), removed from the oil and allowed to air cool to below 66°C (150°F), or until the work-piece can be touched comfortably with a bare hand. When a salt bath is used, the workpiece is quenched into the bath and held long enough to cool to the bath temperature. It is then removed from the bath and allowed to air cool to below 66°C (150°F), or until it can be touched comfortably with a bare hand.
Straightening: any necessary straightening should be done from the quench at any temperature down to 427°C (800°F).
Stress Relieving: heat slowly to 621/677°C (1150/1250°F), hold 1 to 2 hours, then cool in still air.
Tempering: tempering should be performed immediately after quenching and cooling of the workpiece below 66°C (150°F), or as soon as it can be touched comfortably with a bare hand. Typical tempering is performed at 538°C (1000°F) for two hours at temperature followed by air cooling to room temperature. This cycle is repeated twice to obtain triple tempering.
PROPRIETARY Micro-Melt M48 Alloy Internationale Werkstoffäquivalente
Anzeige von 2 von 3 Ergebnissen.
Die Äquivalenzkategorien basieren auf dem Vergleich der chemischen Zusammensetzung und der mechanischen Eigenschaften – prüfen Sie stets die Eignung anhand der für Ihre Anwendung geltenden Spezifikation.
Benötigen Sie die vollständige Liste der 3 internationalen Äquivalente?
Sehen Sie alle 3 äquivalenten Werkstoffgüten mit detaillierter Zuordnung nach Norm, Hersteller und Äquivalenzkategorie.
Kostenlose Registrierung erforderlich • Sofortiger Zugriff
Optimieren Sie die Materialauswahl für Ihre Anwendung - Demo vereinbaren
- 3Querverweise
- 8Zusammensetzung
- -Mechanische Eigenschaften
- 5Physikalische Eigenschaften
- 1Wärmebehandlung
- -Metallographie
- -Zerspanbarkeit
- -Spannung-Dehnung
- -Umformbarkeit
- -Ermüdung
- -Fraktur
- -Schleicher
- -Verbindungen
- -Beschichtungen
- -Abmessungen
- -Tribologie
- -Korrosion
- -Alterung
- -Witterungsbeständigkeit
- -Bestrahlung
- 2Gesamtzahl der Lieferanten