PROPRIETARY Micro-Melt M48 Alloy Takım çelikleri
Veri güncellemeleri
Bu malzemenin 19 özelliği vardır - burada yalnızca bir alt kümesi gösterilmektedir.
Sıcaklıklar ve koşullar genelinde ayrıntılı değerler de dahil olmak üzere tam malzeme özelliklerinin kilidini açın.
Ücretsiz kayıt gereklidir • Anında erişim
PROPRIETARY Micro-Melt M48 Alloy Kimyasal bileşim
Carpenter Technology Corporation, Product Data Sheets,
Tam malzeme performans verilerini mi arıyorsunuz?
Ücretsiz kayıt gereklidir • Anında erişim
PROPRIETARY Micro-Melt M48 Alloy Fiziksel özellikler
Sıcaklık
Bu malzemenin 19 özelliği vardır - burada yalnızca bir alt kümesi gösterilmektedir.
Sıcaklık ve koşullar genelinde ayrıntılı fiziksel özellik değerlerinin kilidini açın.
Ücretsiz kayıt gereklidir • Anında erişim
PROPRIETARY Micro-Melt M48 Alloy Isıl İşlem
- Annealing: heat uniformly to 871°C (1600°F), hold at temperature for two hours, cool slowly at 14°C (25°F) per hour maximum in the furnace to below 538°C (1000°F), and air cool to room temperature.
Hardening: it is customary to use two furnaces to harden Micro-Melt M48 alloy. One furnace is used to preheat the workpiece to 816/843°C (1500/1550°F), and the second is used to rapidly heat the workpiece from the preheating temperature to the hardening temperature of 1149/1204°C (2100/2200°F). Typical soak times are 2-3 minutes at the high temperature.
Quenching: quench in oil or a salt bath maintained at 538/593°C (1000/1100°F). The workpiece should be quenched in oil until it has reached approximately 538/593°C (1000/1100°F) (dull red color), removed from the oil and allowed to air cool to below 66°C (150°F), or until the work-piece can be touched comfortably with a bare hand. When a salt bath is used, the workpiece is quenched into the bath and held long enough to cool to the bath temperature. It is then removed from the bath and allowed to air cool to below 66°C (150°F), or until it can be touched comfortably with a bare hand.
Straightening: any necessary straightening should be done from the quench at any temperature down to 427°C (800°F).
Stress Relieving: heat slowly to 621/677°C (1150/1250°F), hold 1 to 2 hours, then cool in still air.
Tempering: tempering should be performed immediately after quenching and cooling of the workpiece below 66°C (150°F), or as soon as it can be touched comfortably with a bare hand. Typical tempering is performed at 538°C (1000°F) for two hours at temperature followed by air cooling to room temperature. This cycle is repeated twice to obtain triple tempering.
PROPRIETARY Micro-Melt M48 Alloy Uluslararası eşdeğer malzemeler
3 sonuçtan 2 tanesi gösteriliyor.
Eşdeğerlik kategorileri, kimyasal bileşim ve mekanik özellik karşılaştırmalarını gösterir — uygulamanız için geçerli şartnameye göre uygunluğunu her zaman doğrulayın.
3 uluslararası eşdeğerin tam listesine mi ihtiyacınız var?
Standart, üretici ve eşdeğerlik kategorisine göre ayrıntılı eşleştirmeler ile tüm 3 eşdeğer kaliteleri görün.
Ücretsiz kayıt gereklidir • Anında erişim
Uygulamanız için en uygun olan malzeme seçiminizi optimize edin - Demo Rezervasyonu Yapın
- 3Çapraz Referanslar
- 8Bileşim
- -Mekanik Özellikler
- 5Fiziksel Özellikler
- 1Isıl İşlem
- -Metalografi
- -İşlenebilirlik
- -Gerilme-Gerinim
- -Şekillendirilebilirlik
- -Yorulma
- -Kırılma
- -Sürünmek
- -Bağlantılar
- -Kaplamalar
- -Boyutlar
- -Triboloji
- -Korozyon
- -Yaşlanma
- -Hava şartlarına dayanıklılık
- -Radyasyon etkisi
- 2Toplam Tedarikçiler