AA Alclad one side 7075 Aleaciones de aluminio

Grupo de materiales: Aleaciones No Ferrosas / Aleaciones de aluminio

País/Estándar: Estados Unidos / AA

Actualizaciones de datos

Última actualización: 2019-03

Número total de actualizaciones: 1

Historial de actualizaciones

Este material cuenta con 58 propiedades — aquí solo se muestra una parte.

Accede a todas las propiedades del material, incluyendo valores detallados según temperatura y condiciones.

AA Alclad one side 7075 Propiedades físicas

Temperatura

0 - 30°C

Propiedad/Valor

Módulo de elasticidad

69 — 79 GPa

Desbloquea todos los detalles

Densidad

2.6 — 2.9 kg/dm³

Desbloquea todos los detalles

Coeficiente de Poisson

0.33

Desbloquea todos los detalles

Este material cuenta con 58 propiedades — aquí solo se muestra una parte.

Consulta propiedades físicas detalladas en distintas temperaturas y condiciones.

AA Alclad one side 7075 Tratamiento Térmico

The times and temperatures are typical for various forms, sizes and methods of manufacture and may not exactly describe the optimum treatment for a specific item.

The nominal temperatures at which metal is heated (applies both for solution and precipitation heat treatment) should be attained as rapidly as possible and maintained ± 5°C of nominal during the time at temperature.

The time at precipitation heat treatment temperature will depend on time required for load to reach temperature. The times shown are based on rapid heating, with soaking time measured from the time the load reached within 5°C of the applicable temperature.

Material should be quenched from the solution heat-treating temperature as rapidly as possible and with minimum delay after removal from the furnace. Quenching is typically performed by immersion of wrought products in a cold water bath, although some forgings are quenched in hot-water. Quenching may be performed by alternative means such as total immersion in an aqueous polymer solution, liquefied gas, hot water, or boiling water, or by air blast or fog to minimize distortion provided samples from the material. The use of high-velocity high-volume jets of cold water is also effective for some materials.

The aging of aluminum alloy 7075 from any temper to the T73 or T76 temper series requires closer than normal controls on aging practice variables such as time, temperature, heating-up rates, etc., for any given item. In addition to the above, when re-aging material in the T6 temper series to the T73 or T76 temper series, the specific condition of the T6 temper material (such as its property level and other effect of processing variables) is extremely important and will affect the capability of the re-aged material to conform to the requirements specified for the applicable T73 or T76 temper series.

For sheet

With optimum ingot homogenization, heat treating temperatures as high as 500°C are sometimes acceptable.

Temper W: Solution heat treated at 480°C, quenched, naturally aged. With optimum ingot homogenization, heat treating temperatures as high as 500°C are sometimes acceptable.

Temper T6: Solution heat treated at 480°C, quenched, precipitation heat treated ta 120°C for 24 hours. An alternate two-stage treatment comprised of 4 hours at 95°C followed by 8 hours at 155°C also may be used.

Temper T73: Solution heat treated at 480°C, quenched, a two-stage treatment comprised of 6 to 8 hours at 105°C followed by a second-stage of 24-30 hours at 165°C. An alternate two-stage treatment comprised of 6-8 hours at 107°C followed by a second state of 14-18 hours at 168°C may be used providing a heating up of 14°C per hour is used.

Temper T76: Solution heat treated at 480°C, quenched, a two-stage treatment comprised of 3-30 hours at 121°C followed by 15-18 hours at 163°C. An alternate two-stage treatment of 8 hours at 99°C followed by 24-28 hours at 163°C may be used.

Temper T62: Solution heat treated at 480°C, quenched, precipitation heat treated ta 120°C for 24 hours. An alternate two-stage treatment comprised of 4 hours at 95°C followed by 8 hours at 155°C also may be used.

For plate

With optimum ingot homogenization, heat treating temperatures as high as 500°C are sometimes acceptable. For plate thickness over 4 inches and for rod diameters or bar thicknesses over four inches, a maximum temperature of 490°C is recommended to avoid eutectic melting.

Temper W51: Solution heat treated at 480°C, quenched, naturally aged. Stress-relieved by stretching is required to produce a specified amount of permanent set subsequent to solution heat treatment.

Temper W: Solution heat treated at 480°C, quenched, naturally aged.

Temper T651: Solution heat treated at 480°C, quenched, precipitation heat treated at 120°C for 24 hours. An alternate two-stage treatment comprised of 4 hours at 95°C followed by 8 hours at 155°C also may be used. Stress-relieved by stretching is required to produce a specified amount of permanent set prior to any precipitation heat treatment.

Temper T7351: Solution heat treated at 480°C, quenched, a two-stage treatment comprised of 6 to 8 hours at 105°C followed by a second-stage of 24-30 hours at 165°C. An alternate two-stage treatment comprised of 6-8 hours at 107°C followed by a second state of 14-18 hours at 168°C may be used providing a heating up of 14°C per hour is used. Stress-relieved by stretching is required to produce a specified amount of permanent set prior to any precipitation heat treatment.

Temper T7651: Solution heat treated at 480°C, quenched, a two-stage treatment comprised of 3-30 hours at 121°C followed by 15-18 hours at 163°C. An alternate two-stage treatment of 8 hours at 99°C followed by 24-28 hours at 163°C may be used. Stress-relieved by stretching is required to produce a specified amount of permanent set prior to any precipitation heat treatment.

Temper T62: Solution heat treated at 480°C, quenched, precipitation heat treated at 120°C for 24 hours. An alternate two-stage treatment comprised of 4 hours at 95°C followed by 8 hours at 155°C also may be used.

AA Alclad one side 7075 Propiedades mecánicas

Temperatura

0 - 30°C

Propiedad/Valor

Resistencia a la Tracción

≥ 260 MPa

Desbloquea todos los detalles

Alargamiento, A

≥ 5 %

Desbloquea todos los detalles

Límite elástico, Rp0.2

≥ 145 MPa

Desbloquea todos los detalles

¿Buscas información completa sobre propiedades mecánicas para tomar la mejor decisión?

Obtén información completa sobre resistencia, dureza, fatiga y más.

AA Alclad one side 7075 Materiales Internacionales Equivalentes

Mostrando 5 de 5 resultados.

Material

Estándar

País / Productor

Categoría de Equivalencia

Material

A87075

Estándar

UNS

País / Productor

Estados Unidos

Categoría de Equivalencia

Oficial

Material

Alclad 7075

Estándar

País / Productor

Estados Unidos

Categoría de Equivalencia

Implícito

Material

B 209 Alclad 7075

Estándar

ASTM

País / Productor

Estados Unidos

Categoría de Equivalencia

Implícito

Material

Alclad One Side 7075

Estándar

SAE

País / Productor

Estados Unidos

Categoría de Equivalencia

Implícito

Material

Alclad 7075

Estándar

SAE

País / Productor

Estados Unidos

Categoría de Equivalencia

Implícito

Las categorías de equivalencia reflejan comparaciones de composición química y propiedades mecánicas; siempre verifique la idoneidad del material según la especificación aplicable a su aplicación.

¿Necesita la lista completa de los 5 internacionales equivalentes?

Consulte los grados 5 equivalentes con el detalle completo de correspondencias por norma, fabricante y categoría de equivalencia.

Optimiza la selección de materiales para tu aplicación - Reservar una demo

¿Buscas comparar materiales y tomar mejores decisiones?

Accede a datos confiables de materiales, compara opciones y decide con mayor rapidez.

Con Total Materia, puedes:

Comparar materiales basándote en datos reales de ingeniería

Encontrar materiales equivalentes entre distintas normas

Evaluar el desempeño según tus condiciones específicas

Verificar el cumplimiento con normativas internacionales

Descubre cómo funciona para tu aplicación específica

Realizar un Recorrido Guiado

5Referencias cruzadas

-Composición
33Propiedades mecánicas
3Propiedades físicas
1Tratamiento térmico
-Metalografía
-Maquinabilidad

-Esfuerzo-Deformación
-Conformabilidad
-Fatiga
-Fractura
-Bicho raro

14Uniones
-Revestimientos
-Dimensiones
-Tribología

-Corrosión
-Envejecimiento
-Resistencia a la intemperie
-Irradiación

2Proveedores Totales