ASTM F 682 Type II Aciers de construction
Mises à jour des données
Ce matériau a 36 entrées de propriétés – seul un aperçu est visible ici.
Déverrouillez l’accès aux propriétés détaillées du matériau, notamment en température et dans différentes conditions.
Inscription gratuite requise • Accès instantané
ASTM F 682 Type II Composition chimique
F682: 1982 / Norme de spécification pour raccords de tuyauteries de type à manchon en acier au carbone corroyé
Vous souhaitez voir toutes les données sur ce matériau ?
Inscription gratuite requise • Accès instantané
ASTM F 682 Type II Propriétés physiques
Température
Ce matériau a 36 entrées de propriétés – seul un aperçu est visible ici.
Déverrouiller l’accès aux propriétés physiques à différentes températures et conditions.
Inscription gratuite requise • Accès instantané
ASTM F 682 Type II Traitement thermique
- Hot-formed couplings upon which the final forming operation is completed at a temperature above 621°C (1150°F) and below 982°C (1800°F) need not be heat treated provided they are cooled in still air.
Hot-formed couplings finished at a temperature in excess of 982°C (1800°F) shall subsequently be annealed, normalized, or normalized and tempered.
Cold-formed couplings upon which the final forming operation is completed at a temperature below 621°C (1150°F) shall be normalized or shall be stress-relieved at 593 to 677°C (1100 to 1250°F) for 1 h/in. of thickness.
Couplings produced by fusion welding shall be postweld heat treated at 593°C to 677°C (1100°F to 1250°F), when the nominal wall thickness at the welded joint is 3⁄4 in. or greater.
Heat Treatment Procedures - Couplings after forming at an elevated temperature shall be cooled to a temperature below the critical range under suitable conditions to prevent injuries by too rapid cooling, but in no case more rapidly than the cooling rate in still air. Couplings that are to be heat treated shall be treated as follows:
Full Annealing - Couplings shall be uniformly reheated to a temperature above the transformation range and, after being held for a sufficient time at this temperature, cooled slowly to a temperature below the transformation range.
Normalizing - Couplings shall be uniformly reheated to a temperature above the transformation range and subsequently cooled in air at room temperature.
Tempering and Postweld Heat Treatment - Couplings shall be reheated to the prescribed temperature below the transformation range, held at temperature for not less than 1 h ⁄in. of thickness at the thickest section, and cooled in the furnace or in still air.
ASTM F 682 Type II Propriétés mécaniques
Température
Vous avez besoin des propriétés mécaniques détaillées pour faire le bon choix ?
Accédez aux données complètes de résistance, dureté, fatigue et plus encore.
Inscription gratuite requise • Accès instantané
ASTM F 682 Type II Matériaux équivalents internationaux
Affichage de 3 sur 11 résultats.
Les catégories d'équivalence reflètent une comparaison de la composition chimique et des propriétés mécaniques — vérifiez toujours l'adéquation par rapport à la spécification applicable à votre utilisation.
Besoin de la liste complète des 11 équivalents internationaux ?
Consultez les 11 nuances équivalentes avec une correspondance détaillée par norme, producteur et catégorie d'équivalence.
Inscription gratuite requise • Accès instantané
Optimisez les choix de matériaux pour votre application - Réserver une démo
- 11Références croisées
- 4Composition
- 3Propriétés mécaniques
- 3Propriétés physiques
- 1Traitement thermique
- -Métallographie
- -Usinabilité
- -Contrainte-Déformation
- -Formabilité
- -Fatigue
- -Rupture
- -Rampant
- -Assemblages
- -Revêtements
- 13Dimensions
- -Tribologie
- -Corrosion
- -Vieillissement
- -Résistance aux intempéries
- -Irradiation
- 1Fournisseurs totaux