ASTM F 682 Type II Stale konstrukcyjne
Aktualizacje danych
Ten materiał ma 36 właściwości - tutaj pokazano tylko ich część.
Odblokuj pełne właściwości materiału, w tym szczegółowe wartości w różnych temperaturach i warunkach.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
ASTM F 682 Type II Skład chemiczny
F682: 1982 / Specyfikacja standardu dla półfabrykatu złączek rurowych typu rękaw ze stali węglowej
Szukasz pełnych danych o właściwościach materiałów?
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
ASTM F 682 Type II Właściwości fizyczne
Temperatura
Ten materiał ma 36 właściwości - tutaj pokazano tylko ich część.
Odblokuj dostęp do szczegółowych wartości fizycznych w różnych temperaturach i warunkach.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
ASTM F 682 Type II Obróbka cieplna
- Hot-formed couplings upon which the final forming operation is completed at a temperature above 621°C (1150°F) and below 982°C (1800°F) need not be heat treated provided they are cooled in still air.
Hot-formed couplings finished at a temperature in excess of 982°C (1800°F) shall subsequently be annealed, normalized, or normalized and tempered.
Cold-formed couplings upon which the final forming operation is completed at a temperature below 621°C (1150°F) shall be normalized or shall be stress-relieved at 593 to 677°C (1100 to 1250°F) for 1 h/in. of thickness.
Couplings produced by fusion welding shall be postweld heat treated at 593°C to 677°C (1100°F to 1250°F), when the nominal wall thickness at the welded joint is 3⁄4 in. or greater.
Heat Treatment Procedures - Couplings after forming at an elevated temperature shall be cooled to a temperature below the critical range under suitable conditions to prevent injuries by too rapid cooling, but in no case more rapidly than the cooling rate in still air. Couplings that are to be heat treated shall be treated as follows:
Full Annealing - Couplings shall be uniformly reheated to a temperature above the transformation range and, after being held for a sufficient time at this temperature, cooled slowly to a temperature below the transformation range.
Normalizing - Couplings shall be uniformly reheated to a temperature above the transformation range and subsequently cooled in air at room temperature.
Tempering and Postweld Heat Treatment - Couplings shall be reheated to the prescribed temperature below the transformation range, held at temperature for not less than 1 h ⁄in. of thickness at the thickest section, and cooled in the furnace or in still air.
ASTM F 682 Type II Właściwości mechaniczne
Temperatura
Potrzebujesz kompletnych właściwości mechanicznych, aby dokonać właściwego wyboru?
Uzyskaj kompletne dane dotyczące wytrzymałości, twardości, zmęczenia i innych parametrów.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
ASTM F 682 Type II Międzynarodowe materiały równoważne
Wyświetlanie 3 ze 11 wyników.
Kategorie równoważności odzwierciedlają porównanie składu chemicznego i właściwości mechanicznych - zawsze należy zweryfikować przydatność względem specyfikacji obowiązującej dla danego zastosowania.
Potrzebujesz pełną listę 11 międzynarodowych odpowiedników?
Zobacz pełną listę 11 równoważnych materiałów wraz ze szczegółowym przyporządkowaniem według normy, producenta i kategorii równoważności.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
Zoptymalizuj dobór materiałów do swojego zastosowania - Umów się na prezentację
- 11Odniesienia
- 4Skład Chemiczny
- 3Właściwości Mechaniczne
- 3Właściwości Fizyczne
- 1Obróbka Cieplna
- -Metalografia
- -Obrabialność
- -Naprężenie-Odkształcenie
- -Plastyczność
- -Zmęczenie materiału
- -Pęknięcie
- -Pełzać
- -Złącza
- -Powłoki
- 13Wymiary
- -Trybologia
- -Korozja
- -Starzenie
- -Odporność na warunki atmosferyczne
- -Napromieniowanie
- 1Łączna liczba dostawców