ASTM F 682 Type II Aços estruturais e de construcão
Atualizações de dados
Este material conta com 36 propriedades — apenas uma parte está sendo exibida aqui.
Desbloqueie todas as propriedades do material, incluindo valores detalhados em diferentes temperaturas e condições.
Registro gratuito requerido • Acesso instantâneo
ASTM F 682 Type II Composição química
F682: 1982 / Especificações padrão para acoplamentos de tubulações de aço carbono forjado do tipo manga
Precisa de dados completos de desempenho de materiais?
Registro gratuito requerido • Acesso instantâneo
ASTM F 682 Type II Propriedades físicas
Temperatura
Este material conta com 36 propriedades — apenas uma parte está sendo exibida aqui.
Desbloquear valores físicos específicos em diferentes temperaturas e condições.
Registro gratuito requerido • Acesso instantâneo
ASTM F 682 Type II Tratamento Térmico
- Hot-formed couplings upon which the final forming operation is completed at a temperature above 621°C (1150°F) and below 982°C (1800°F) need not be heat treated provided they are cooled in still air.
Hot-formed couplings finished at a temperature in excess of 982°C (1800°F) shall subsequently be annealed, normalized, or normalized and tempered.
Cold-formed couplings upon which the final forming operation is completed at a temperature below 621°C (1150°F) shall be normalized or shall be stress-relieved at 593 to 677°C (1100 to 1250°F) for 1 h/in. of thickness.
Couplings produced by fusion welding shall be postweld heat treated at 593°C to 677°C (1100°F to 1250°F), when the nominal wall thickness at the welded joint is 3⁄4 in. or greater.
Heat Treatment Procedures - Couplings after forming at an elevated temperature shall be cooled to a temperature below the critical range under suitable conditions to prevent injuries by too rapid cooling, but in no case more rapidly than the cooling rate in still air. Couplings that are to be heat treated shall be treated as follows:
Full Annealing - Couplings shall be uniformly reheated to a temperature above the transformation range and, after being held for a sufficient time at this temperature, cooled slowly to a temperature below the transformation range.
Normalizing - Couplings shall be uniformly reheated to a temperature above the transformation range and subsequently cooled in air at room temperature.
Tempering and Postweld Heat Treatment - Couplings shall be reheated to the prescribed temperature below the transformation range, held at temperature for not less than 1 h ⁄in. of thickness at the thickest section, and cooled in the furnace or in still air.
ASTM F 682 Type II Propriedades mecânicas
Temperatura
Precisa de propriedades mecânicas completas para fazer a escolha certa?
Acesse dados detalhados de resistência, dureza, fadiga e muito mais.
Registro gratuito requerido • Acesso instantâneo
ASTM F 682 Type II Materiais Equivalentes Internacionais
Exibindo 3 de 11 resultados.
As categorias de equivalência refletem a comparação da composição química e das propriedades mecânicas, sempre verifique a adequação do material em relação à especificação aplicável à sua aplicação.
Precisa da lista completa do 11 de equivalentes internacionais?
Veja todos as classes 11 equivalentes com mapeamento detalhado por norma, fabricante e categoria de equivalência.
Registro gratuito requerido • Acesso instantâneo
Otimizar seleção de materiais para sua aplicação - Agende uma demonstração
- 11Referências Cruzadas
- 4Composição
- 3Propriedades Mecânicas
- 3Propriedades físicas
- 1Tratamento térmico
- -Metalografia
- -Usinabilidade
- -Tensão-Deformação
- -Conformabilidade
- -Fadiga
- -Fratura
- -Rastejante
- -Junta
- -Revestimentos
- 13Dimensões
- -Tribologia
- -Corrosão
- -Envelhecimento
- -Resistência às Intempéries
- -Irradiação
- 1Total de Fornecedores