ASTM F 682 Type II Aceros estructurales y de construcción
Actualizaciones de datos
Este material cuenta con 36 propiedades — aquí solo se muestra una parte.
Accede a todas las propiedades del material, incluyendo valores detallados según temperatura y condiciones.
Se requiere registro gratuito • Acceso inmediato
ASTM F 682 Type II Composición química
F682: 1982 / Especificación estándar para acoplamiento de tuberías Tipo-Manga de acero al carbono forjado
¿Buscas datos completos de desempeño de materiales?
Se requiere registro gratuito • Acceso inmediato
ASTM F 682 Type II Propiedades físicas
Temperatura
Este material cuenta con 36 propiedades — aquí solo se muestra una parte.
Consulta propiedades físicas detalladas en distintas temperaturas y condiciones.
Se requiere registro gratuito • Acceso inmediato
ASTM F 682 Type II Tratamiento Térmico
- Hot-formed couplings upon which the final forming operation is completed at a temperature above 621°C (1150°F) and below 982°C (1800°F) need not be heat treated provided they are cooled in still air.
Hot-formed couplings finished at a temperature in excess of 982°C (1800°F) shall subsequently be annealed, normalized, or normalized and tempered.
Cold-formed couplings upon which the final forming operation is completed at a temperature below 621°C (1150°F) shall be normalized or shall be stress-relieved at 593 to 677°C (1100 to 1250°F) for 1 h/in. of thickness.
Couplings produced by fusion welding shall be postweld heat treated at 593°C to 677°C (1100°F to 1250°F), when the nominal wall thickness at the welded joint is 3⁄4 in. or greater.
Heat Treatment Procedures - Couplings after forming at an elevated temperature shall be cooled to a temperature below the critical range under suitable conditions to prevent injuries by too rapid cooling, but in no case more rapidly than the cooling rate in still air. Couplings that are to be heat treated shall be treated as follows:
Full Annealing - Couplings shall be uniformly reheated to a temperature above the transformation range and, after being held for a sufficient time at this temperature, cooled slowly to a temperature below the transformation range.
Normalizing - Couplings shall be uniformly reheated to a temperature above the transformation range and subsequently cooled in air at room temperature.
Tempering and Postweld Heat Treatment - Couplings shall be reheated to the prescribed temperature below the transformation range, held at temperature for not less than 1 h ⁄in. of thickness at the thickest section, and cooled in the furnace or in still air.
ASTM F 682 Type II Propiedades mecánicas
Temperatura
¿Buscas información completa sobre propiedades mecánicas para tomar la mejor decisión?
Obtén información completa sobre resistencia, dureza, fatiga y más.
Se requiere registro gratuito • Acceso inmediato
ASTM F 682 Type II Materiales Internacionales Equivalentes
Mostrando 3 de 11 resultados.
Las categorías de equivalencia reflejan comparaciones de composición química y propiedades mecánicas; siempre verifique la idoneidad del material según la especificación aplicable a su aplicación.
¿Necesita la lista completa de los 11 internacionales equivalentes?
Consulte los grados 11 equivalentes con el detalle completo de correspondencias por norma, fabricante y categoría de equivalencia.
Se requiere registro gratuito • Acceso inmediato
Optimiza la selección de materiales para tu aplicación - Reservar una demo
- 11Referencias cruzadas
- 4Composición
- 3Propiedades mecánicas
- 3Propiedades físicas
- 1Tratamiento térmico
- -Metalografía
- -Maquinabilidad
- -Esfuerzo-Deformación
- -Conformabilidad
- -Fatiga
- -Fractura
- -Bicho raro
- -Uniones
- -Revestimientos
- 13Dimensiones
- -Tribología
- -Corrosión
- -Envejecimiento
- -Resistencia a la intemperie
- -Irradiación
- 1Proveedores Totales