ASME SA-522 Type I Aciers de construction
Mises à jour des données
Ce matériau a 145 entrées de propriétés – seul un aperçu est visible ici.
Déverrouillez l’accès aux propriétés détaillées du matériau, notamment en température et dans différentes conditions.
Inscription gratuite requise • Accès instantané
ASME SA-522 Type I Composition chimique
ASME Boiler and Pressure Vessel Code An International Code Section II - Part A Ferrous Material Specifications, American Society of Mechanical Engineers, 2025
Vous souhaitez voir toutes les données sur ce matériau ?
Inscription gratuite requise • Accès instantané
ASME SA-522 Type I Propriétés physiques
Température
Ce matériau a 145 entrées de propriétés – seul un aperçu est visible ici.
Déverrouiller l’accès aux propriétés physiques à différentes températures et conditions.
Inscription gratuite requise • Accès instantané
ASME SA-522 Type I Traitement thermique
- Quenched and Tempered - Heat to a uniform temperature of 800 ± 15°C (1475 ± 25°F); hold at this temperature for a minimum time of 2.5 min/mm of thickness but in no case less than 30 min; quench by immersion in circulating water. Reheat until the forging attains a uniform temperature within the range from 565 to 605°C (1050 to 1125°F); hold at this temperature for a minimum time of 2.5 min/mm of thickness but in no case less than 30 min; cool in air or water quench, at a rate not less than 167°C (300°F)/h.
Double Normalized and Tempered - Heat to a uniform temperature of 900°C (1650°F); hold at this temperature for a minimum time of 2.5 min/mm of thickness but in no case less than 30 min; cool in air. Reheat until the forging attains a uniform temperature of 790°C (1450°F); hold at this temperature for a minimum time of 2.5 min/mm of thickness but in no case less than 30 min; cool in air. Reheat to a uniform temperature within the range from 565 to 605°C (1050 to 1125°F); hold at this temperature for a minimum time of 2.5 min/mm of thickness but in no case less than 30 min; cool in air or water quench, at a rate not less than 167°C (300°F)/h.
When stress relieving is to be performed after fabrication, the recommended stress-relieving treatment is as follows: gradually and uniformly heat the steel to a temperature between 550 and 585°C (1025 and 1085°F); hold for a minimum of 2 h for thicknesses up to 25 mm. For thicknesses over 25 mm, a minimum additional holding time in the ratio of 2.5 min/mm of thickness in excess of 25 mm shall be added. Cool at a minimum rate of 167°C (300°F)/h to a temperature not exceeding 315°C (600°F).
ASME SA-522 Type I Propriétés mécaniques
Température
Vous avez besoin des propriétés mécaniques détaillées pour faire le bon choix ?
Accédez aux données complètes de résistance, dureté, fatigue et plus encore.
Inscription gratuite requise • Accès instantané
ASME SA-522 Type I Matériaux équivalents internationaux
Affichage de 3 résultats sur 39.
Les catégories d'équivalence reflètent la comparaison de la composition chimique et des propriétés mécaniques — vérifiez toujours l'adéquation avec la spécification applicable à votre application.
Besoin de la liste complète des 39 équivalents internationaux ?
Consultez les 39 nuances équivalentes avec une cartographie détaillée par norme, producteur et catégorie d'équivalence.
Inscription gratuite requise • Accès instantané
Optimisez les choix de matériaux pour votre application - Réserver une démo
- 39Références croisées
- 6Composition
- 16Propriétés mécaniques
- 59Propriétés physiques
- 1Traitement thermique
- -Métallographie
- -Usinabilité
- -Contrainte-Déformation
- -Formabilité
- -Fatigue
- -Rupture
- 24Rampant
- -Assemblages
- -Revêtements
- -Dimensions
- -Tribologie
- -Corrosion
- -Vieillissement
- -Résistance aux intempéries
- -Irradiation
- -Fournisseurs totaux