ASME SA-522 Type I Stale konstrukcyjne
Aktualizacje danych
Ten materiał ma 145 właściwości - tutaj pokazano tylko ich część.
Odblokuj pełne właściwości materiału, w tym szczegółowe wartości w różnych temperaturach i warunkach.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
ASME SA-522 Type I Skład chemiczny
ASME Boiler and Pressure Vessel Code An International Code Section II - Part A Ferrous Material Specifications, American Society of Mechanical Engineers, 2025
Szukasz pełnych danych o właściwościach materiałów?
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
ASME SA-522 Type I Właściwości fizyczne
Temperatura
Ten materiał ma 145 właściwości - tutaj pokazano tylko ich część.
Odblokuj dostęp do szczegółowych wartości fizycznych w różnych temperaturach i warunkach.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
ASME SA-522 Type I Obróbka cieplna
- Quenched and Tempered - Heat to a uniform temperature of 800 ± 15°C (1475 ± 25°F); hold at this temperature for a minimum time of 2.5 min/mm of thickness but in no case less than 30 min; quench by immersion in circulating water. Reheat until the forging attains a uniform temperature within the range from 565 to 605°C (1050 to 1125°F); hold at this temperature for a minimum time of 2.5 min/mm of thickness but in no case less than 30 min; cool in air or water quench, at a rate not less than 167°C (300°F)/h.
Double Normalized and Tempered - Heat to a uniform temperature of 900°C (1650°F); hold at this temperature for a minimum time of 2.5 min/mm of thickness but in no case less than 30 min; cool in air. Reheat until the forging attains a uniform temperature of 790°C (1450°F); hold at this temperature for a minimum time of 2.5 min/mm of thickness but in no case less than 30 min; cool in air. Reheat to a uniform temperature within the range from 565 to 605°C (1050 to 1125°F); hold at this temperature for a minimum time of 2.5 min/mm of thickness but in no case less than 30 min; cool in air or water quench, at a rate not less than 167°C (300°F)/h.
When stress relieving is to be performed after fabrication, the recommended stress-relieving treatment is as follows: gradually and uniformly heat the steel to a temperature between 550 and 585°C (1025 and 1085°F); hold for a minimum of 2 h for thicknesses up to 25 mm. For thicknesses over 25 mm, a minimum additional holding time in the ratio of 2.5 min/mm of thickness in excess of 25 mm shall be added. Cool at a minimum rate of 167°C (300°F)/h to a temperature not exceeding 315°C (600°F).
ASME SA-522 Type I Właściwości mechaniczne
Temperatura
Potrzebujesz kompletnych właściwości mechanicznych, aby dokonać właściwego wyboru?
Uzyskaj kompletne dane dotyczące wytrzymałości, twardości, zmęczenia i innych parametrów.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
ASME SA-522 Type I Międzynarodowe materiały równoważne
Wyświetlanie 3 z 39 wyników.
Kategorie równoważności odzwierciedlają porównanie składu chemicznego i właściwości mechanicznych — zawsze należy sprawdzić przydatność względem obowiązującej specyfikacji dla danego zastosowania.
Potrzebujesz pełnej listy 39 międzynarodowych odpowiedników?
Zobacz wszystkie 39 równoważne gatunki ze szczegółowym mapowaniem według normy, producenta i kategorii równoważności.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
Zoptymalizuj dobór materiałów do swojego zastosowania - Umów się na prezentację
- 39Odniesienia
- 6Skład Chemiczny
- 16Właściwości Mechaniczne
- 59Właściwości Fizyczne
- 1Obróbka Cieplna
- -Metalografia
- -Obrabialność
- -Naprężenie-Odkształcenie
- -Plastyczność
- -Zmęczenie materiału
- -Pęknięcie
- 24Pełzać
- -Złącza
- -Powłoki
- -Wymiary
- -Trybologia
- -Korozja
- -Starzenie
- -Odporność na warunki atmosferyczne
- -Napromieniowanie
- -Łączna liczba dostawców