PROPRIETARY Uddeholm Vanadis 60 SuperClean Tool steels

Material group: Ferrous Alloys / Tool steels

Country / Standard: PROPRIETARY

Data updates

Latest Update: 2021-01

Total number of updates: 2

Update History

2016-04

This material has 51 properties — only a subset is shown here.

Unlock full material properties, including detailed values across temperatures and conditions.

PROPRIETARY Uddeholm Vanadis 60 SuperClean Chemical Composition

CRITERIA

VALUE

UNIT

CAS NUMBER

CRITERIA

VALUE

2.3

UNIT

CAS NUMBER

7440-44-0

CRITERIA

VALUE

10.5

UNIT

CAS NUMBER

7440-48-4

CRITERIA

VALUE

4.2

UNIT

CAS NUMBER

7440-47-3

CRITERIA

VALUE

val1

UNIT

CAS NUMBER

7439-98-7

CRITERIA

VALUE

val1

UNIT

CAS NUMBER

7440-62-2

CRITERIA

VALUE

val1

UNIT

CAS NUMBER

7440-33-7

Uddeholms AB, Product Data Sheets,

Looking for full material performance data?

PROPRIETARY Uddeholm Vanadis 60 SuperClean Physical Properties

Temperature

0 - 30°C 30 - 100°C 100 - 300°C ≥ 300°C

PROPERTY / VALUE

Modulus of Elasticity

190 — 250 GPa

Unlock full details

Density

val1 kg/dm³

Unlock full details

Thermal Conductivity

21 W/(m∙°C)

Unlock full details

Heat Capacity

val1 J/(kg∙°C)

Unlock full details

Poisson Coefficient

val1

Unlock full details

This material has 51 properties — only a subset is shown here.

Unlock detailed physical values across temperatures and conditions.

PROPRIETARY Uddeholm Vanadis 60 SuperClean Heat Treatments

Soft annealing:
Protect the steel and heat through to 850-900°C (1560-1650°F). Then cool in the furnace at 10°C/h (20°F/h) to 700°C (1290°F), then freely in air;
Stress relieving:
After rough machining the tool should be heated through to 600-700°C (1110-1290°F), holding time 2 hr. Cool slowly to 500°C (930°F), then freely in air;
Tempering:
Pre-heating temperature: 450-500°C (840-930°F) and 850-900°C (1560-1650°F).
Austenitizing temperature: 1100-1180°C (2010-2160°F), according to the desired final hardness. (The tool should be protected against decarburization and oxidation during hardening.
Quenching media:
Martempering bath at approx. 540°C (1000°F), Vacuum furnace with high speed gas at sufficient overpressure (Quenching should be continued until the temperature of the tool reaches approx. 25°C (77°F). The tool should then be tempered immediately; In order to obtain a high toughness, the cooling speed in the core should be at least 10°C/sec (20°F/sec). This is valid for cooling from the austenitizing temperature down to approx. 540°C (1000°F). After temperature equalization between the surface and core, the cooling rate of approx. 5°C/sec (10°F/sec) can be used.);
Tempering:
For cold work applications tempering should always be carried out at 560°C (1040°F) irrespective of the austenitizing temperature. Temper three times for one hour at full temperature. The tool should be cooled to room temperature between the tempers. The retained austenite content will be less than 1% after this tempering cycle.
Sub-zero treatment:
It should be treated immediately after quenching between -150 and -196°C (-238 and -321°F), although occasionally -70 to -80°C (-95 to -110°F) are used.
Austenitizing temperature 1150°C (1920°F). Holding time 10 minutes.

PROPRIETARY Uddeholm Vanadis 60 SuperClean Mechanical Properties

Temperature

0 - 30°C

PROPERTY / VALUE

Brinell Hardness (HB)

≤ 340

Unlock full details

Rockwell Hardness (HR)

62 — 69

Unlock full details

Need complete mechanical properties to make the right choice?

Get complete data on strength, hardness, fatigue, and more.

PROPRIETARY Uddeholm Vanadis 60 SuperClean International Equivalent Materials

Showing 6 of 7 results.

MATERIAL

STANDARD

COUNTRY / PRODUCER

EQUIVALENCE CATEGORY

MATERIAL

ASP 2060

STANDARD

PROPRIETARY

COUNTRY / PRODUCER

EQUIVALENCE CATEGORY

Composition 100%

MATERIAL

PMD60

STANDARD

PROPRIETARY

COUNTRY / PRODUCER

EQUIVALENCE CATEGORY

Composition 100%

MATERIAL

1.3241 HTM (60)

STANDARD

PROPRIETARY

COUNTRY / PRODUCER

EQUIVALENCE CATEGORY

Composition 100%

MATERIAL

Assab ASP 60

STANDARD

PROPRIETARY

COUNTRY / PRODUCER

EQUIVALENCE CATEGORY

Composition 100%

MATERIAL

Vibenite 280

STANDARD

PROPRIETARY

COUNTRY / PRODUCER

EQUIVALENCE CATEGORY

Composition 100%

MATERIAL

LO-QPM 60

STANDARD

PROPRIETARY

COUNTRY / PRODUCER

EQUIVALENCE CATEGORY

Composition 100%

Equivalence categories reflect chemical-composition and mechanical-property comparison — always verify suitability against the governing specification for your application.

Need the full list of 7 international equivalents?

See all 7 equivalent grades with detailed mapping by standard, producer and equivalence category.

Optimize material selection for your application - Book A Demo

Looking to compare materials and make better decisions?

Access reliable material data, compare options, and make better decisions faster.

With Total Materia, you can:

Compare materials based on real engineering data

Find equivalent materials across standards

Evaluate performance for your specific conditions

Check compliance with global regulations

See how this works for your specific application

Take a Guided Tour

7Cross References

6Composition
6Mechanical Properties
21Physical Properties
2Heat Treatment
-Metallography
-Machinability

-Stress-Strain
-Formability
-Fatigue
-Fracture
-Creep

-Joints
-Coatings
-Dimensions
-Tribology

-Corrosion
-Ageing
-Weatherability
-Irradiation

9Total Suppliers