PROPRIETARY HG 2363 Takım çelikleri
Veri güncellemeleri
Bu malzemenin 142 özelliği vardır - burada yalnızca bir alt kümesi gösterilmektedir.
Sıcaklıklar ve koşullar genelinde ayrıntılı değerler de dahil olmak üzere tam malzeme özelliklerinin kilidini açın.
Ücretsiz kayıt gereklidir • Anında erişim
PROPRIETARY HG 2363 Kimyasal bileşim
Cold Work Tool Steels, HG2510, Huang Limited, 2017
Tam malzeme performans verilerini mi arıyorsunuz?
Ücretsiz kayıt gereklidir • Anında erişim
PROPRIETARY HG 2363 Fiziksel özellikler
Sıcaklık
Bu malzemenin 142 özelliği vardır - burada yalnızca bir alt kümesi gösterilmektedir.
Sıcaklık ve koşullar genelinde ayrıntılı fiziksel özellik değerlerinin kilidini açın.
Ücretsiz kayıt gereklidir • Anında erişim
PROPRIETARY HG 2363 Isıl İşlem
- Forging:
Preheat at 650-680°C before raising the temperature to 1050-1100°C and soak until uniformly heated. Initial hammer blows should be light due to the comparatively high hot strength of this steel. The forging temperature must be maintained above 1000°C until the metal begins to yield. Final forging should not be done below 900°C. Slow cooling after forging is essential to avoid the possibility of cracking.
Annealing:
A2 tool steel is supplied in the annealed condition. Re-annealing will only be necessary if the toolmaker has forged the steel, or if a hardened tool has to be re-machined or re-hardened. Heat slowly to 850-870°C. After a minimum of two hours at this temperature the furnace temperature should be lowered to 730-750°C and held there for four to six hours. Allow to cool very slowly in the furnace to 600°C or below before removing the steel to cool in air
Stress Relieving:
When heavy machining and-or grinding of A2 tool steel has been carried out, it is advisable to stress relieve in order to minimize the danger of distortion or cracking during the subsequent heat treatment. To stress-relieve, heat the tools slowly to 670-700oC, soak for a minimum of two hours per 25mm of section and allow to cool down in the furnace. The tools can then be finish machined, leaving on an allowance for final grinding after hardening and tempering.
Hardening:
Pre-heat slowly to 790-820°C and thoroughly soak at this temperature. Continue heating to the hardening temperature of 950-980°C. Allow sufficient time for the A2 tool steel component to become evenly heated through. Withdraw from the furnace and then either air cool or oil quench. The steel may be protected against scaling and decarburization by heating in a reducing atmosphere furnace, heating in a neutral salt bath, or by pack hardening. Temper as soon as the tool is hand warm
Tempering:
Double tempering is recommended. Soak well at the selected temperature and soak for at least one hour per 25mm of total thickness.
PROPRIETARY HG 2363 Mekanik özellikler
Sıcaklık
Doğru seçimi yapmak için eksiksiz mekanik özelliklere mi ihtiyacınız var?
Mukavemet, sertlik, yorulma ve daha fazlası hakkında eksiksiz verilere ulaşın.
Ücretsiz kayıt gereklidir • Anında erişim
PROPRIETARY HG 2363 Uluslararası eşdeğer malzemeler
69 sonuçtan 15 tanesi gösteriliyor.
Eşdeğerlik kategorileri kimyasal bileşim ve mekanik özellik karşılaştırmasını yansıtır — uygulamanız için uygunluğu her zaman geçerli şartnameye göre doğrulayın.
69 uluslararası eşdeğerin tam listesine mi ihtiyacınız var?
Standart, üretici ve eşdeğerlik kategorisine göre ayrıntılı eşleştirme ile 69 eşdeğer kaliteyi görüntüleyin.
Ücretsiz kayıt gereklidir • Anında erişim
Uygulamanız için en uygun olan malzeme seçiminizi optimize edin - Demo Rezervasyonu Yapın
- 69Çapraz Referanslar
- 8Bileşim
- 2Mekanik Özellikler
- 3Fiziksel Özellikler
- 2Isıl İşlem
- -Metalografi
- -İşlenebilirlik
- -Gerilme-Gerinim
- -Şekillendirilebilirlik
- -Yorulma
- -Kırılma
- -Sürünmek
- -Bağlantılar
- -Kaplamalar
- -Boyutlar
- -Triboloji
- -Korozyon
- -Yaşlanma
- -Hava şartlarına dayanıklılık
- -Radyasyon etkisi
- 58Toplam Tedarikçiler