SAE Ti-10V-2Fe-3Al Titanium Alloys
Atualizações de dados
Este material conta com 4475 propriedades — apenas uma parte está sendo exibida aqui.
Desbloqueie todas as propriedades do material, incluindo valores detalhados em diferentes temperaturas e condições.
Registro gratuito requerido • Acesso instantâneo
SAE Ti-10V-2Fe-3Al Composição química
SAE AMS 4983G: 2019 / Ligas de titanio, forjagens 10V - 2Fe - 3Al Electrodo consumivel, Tratamento térmico de solução num unico passo e envelhecido 180 ksi (1241 MPa) Resistência à tracção
Precisa de dados completos de desempenho de materiais?
Registro gratuito requerido • Acesso instantâneo
SAE Ti-10V-2Fe-3Al Propriedades físicas
Temperatura
Este material conta com 4475 propriedades — apenas uma parte está sendo exibida aqui.
Desbloquear valores físicos específicos em diferentes temperaturas e condições.
Registro gratuito requerido • Acesso instantâneo
SAE Ti-10V-2Fe-3Al Tratamento Térmico
- Solution Heat Treatment
Forgings shall be heated to a temperature 60 to 100°F (33 to 56°C) below the beta transus, held at heat for not less than 30 minutes, and quenched in water, unless a double solution heat treatment is specified by purchaser. In that case forgings shall be also heated to a temperature 60 to 100°F (33 to 56°C) below the beta transus, held at heat for not less than 30 minutes, and either furnace cooled or air cooled to room temperature.
Aging heat treatment: heat to a temperature within the range 900 to 975°F (482 to 524°C), hold at the selected temperature within ±10 °F (±6°C) for not less than 8 hours, and cool to room temperature.
Beta Transus Determination:
The beta transus temperature shall be determined by metallography, differential thermal analyzer, calculated from chemical composition of the alloy, or any method acceptable to purchaser. Thermal controls and readouts shall be calibrated to an accuracy of ±5°F (±3°C). - Solution Heat Treatment
Forgings shall be single solution heat treated by heating to a temperature 60 to 100°F (33 to 55°C) degrees below the beta transus, holding at heat for not less than 30 minutes, and cooling at a rate equivalent to an air cool or faster.
Beta Transus Determination
The beta transus temperature shall be determined by metallography, differential thermal analyzer, calculated from the chemical composition of the alloy, or a method acceptable to purchaser Thermal controls and readouts shall be calibrated to an accuracy of ±5°F (±3°C).
Aging
Heat to a temperature not lower than 900°F (482°C), hold at the selected temperature within ±10°F (±6°C) for not less than 8 hours, and cool to room temperature.
SAE Ti-10V-2Fe-3Al Propriedades mecânicas
Temperatura
Precisa de propriedades mecânicas completas para fazer a escolha certa?
Acesse dados detalhados de resistência, dureza, fadiga e muito mais.
Registro gratuito requerido • Acesso instantâneo
SAE Ti-10V-2Fe-3Al Materiais Equivalentes Internacionais
Exibindo 8 de 32 resultados.
As categorias de equivalência refletem a comparação da composição química e das propriedades mecânicas, sempre verifique a adequação do material em relação à especificação aplicável à sua aplicação.
Precisa da lista completa do 32 de equivalentes internacionais?
Veja todos as classes 32 equivalentes com mapeamento detalhado por norma, fabricante e categoria de equivalência.
Registro gratuito requerido • Acesso instantâneo
Otimizar seleção de materiais para sua aplicação - Agende uma demonstração
- 32Referências Cruzadas
- 44Composição
- 51Propriedades Mecânicas
- 10Propriedades físicas
- 6Tratamento térmico
- -Metalografia
- -Usinabilidade
- 26Tensão-Deformação
- -Conformabilidade
- 7Fadiga
- 4Fratura
- -Rastejante
- -Junta
- -Revestimentos
- -Dimensões
- -Tribologia
- 4283Corrosão
- -Envelhecimento
- -Resistência às Intempéries
- -Irradiação
- 12Total de Fornecedores