SAE Ti-10V-2Fe-3Al Stopy tytanu
Aktualizacje danych
Ten materiał ma 4475 właściwości - tutaj pokazano tylko ich część.
Odblokuj pełne właściwości materiału, w tym szczegółowe wartości w różnych temperaturach i warunkach.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
SAE Ti-10V-2Fe-3Al Skład chemiczny
SAE AMS 4983G: 2019 / Stop tytanu na odkuwki, 10V - 2Fe - 3Al, obrobiony cieplnie do granicy wytrzymałości na rozciąganie 180 ksi (1241 MPa)
Szukasz pełnych danych o właściwościach materiałów?
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
SAE Ti-10V-2Fe-3Al Właściwości fizyczne
Temperatura
Ten materiał ma 4475 właściwości - tutaj pokazano tylko ich część.
Odblokuj dostęp do szczegółowych wartości fizycznych w różnych temperaturach i warunkach.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
SAE Ti-10V-2Fe-3Al Obróbka cieplna
- Solution Heat Treatment
Forgings shall be heated to a temperature 60 to 100°F (33 to 56°C) below the beta transus, held at heat for not less than 30 minutes, and quenched in water, unless a double solution heat treatment is specified by purchaser. In that case forgings shall be also heated to a temperature 60 to 100°F (33 to 56°C) below the beta transus, held at heat for not less than 30 minutes, and either furnace cooled or air cooled to room temperature.
Aging heat treatment: heat to a temperature within the range 900 to 975°F (482 to 524°C), hold at the selected temperature within ±10 °F (±6°C) for not less than 8 hours, and cool to room temperature.
Beta Transus Determination:
The beta transus temperature shall be determined by metallography, differential thermal analyzer, calculated from chemical composition of the alloy, or any method acceptable to purchaser. Thermal controls and readouts shall be calibrated to an accuracy of ±5°F (±3°C). - Solution Heat Treatment
Forgings shall be single solution heat treated by heating to a temperature 60 to 100°F (33 to 55°C) degrees below the beta transus, holding at heat for not less than 30 minutes, and cooling at a rate equivalent to an air cool or faster.
Beta Transus Determination
The beta transus temperature shall be determined by metallography, differential thermal analyzer, calculated from the chemical composition of the alloy, or a method acceptable to purchaser Thermal controls and readouts shall be calibrated to an accuracy of ±5°F (±3°C).
Aging
Heat to a temperature not lower than 900°F (482°C), hold at the selected temperature within ±10°F (±6°C) for not less than 8 hours, and cool to room temperature.
SAE Ti-10V-2Fe-3Al Właściwości mechaniczne
Temperatura
Potrzebujesz kompletnych właściwości mechanicznych, aby dokonać właściwego wyboru?
Uzyskaj kompletne dane dotyczące wytrzymałości, twardości, zmęczenia i innych parametrów.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
SAE Ti-10V-2Fe-3Al Międzynarodowe materiały równoważne
Wyświetlanie 8 ze 32 wyników.
Kategorie równoważności odzwierciedlają porównanie składu chemicznego i właściwości mechanicznych - zawsze należy zweryfikować przydatność względem specyfikacji obowiązującej dla danego zastosowania.
Potrzebujesz pełną listę 32 międzynarodowych odpowiedników?
Zobacz pełną listę 32 równoważnych materiałów wraz ze szczegółowym przyporządkowaniem według normy, producenta i kategorii równoważności.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
Zoptymalizuj dobór materiałów do swojego zastosowania - Umów się na prezentację
- 32Odniesienia
- 44Skład Chemiczny
- 51Właściwości Mechaniczne
- 10Właściwości Fizyczne
- 6Obróbka Cieplna
- -Metalografia
- -Obrabialność
- 26Naprężenie-Odkształcenie
- -Plastyczność
- 7Zmęczenie materiału
- 4Pęknięcie
- -Pełzać
- -Złącza
- -Powłoki
- -Wymiary
- -Trybologia
- 4283Korozja
- -Starzenie
- -Odporność na warunki atmosferyczne
- -Napromieniowanie
- 12Łączna liczba dostawców