SAE Ti-10V-2Fe-3Al Titanium Alloys
Actualizaciones de datos
Este material cuenta con 4475 propiedades — aquí solo se muestra una parte.
Accede a todas las propiedades del material, incluyendo valores detallados según temperatura y condiciones.
Se requiere registro gratuito • Acceso inmediato
SAE Ti-10V-2Fe-3Al Composición química
SAE AMS 4983G: 2019 / Aleación de titanio, piezas forjadas 10V - 2Fe - 3Al Electrodo consumible fundido, Térmicamente tratadas por solución de un simple paso y Envejecidas, Resistencia a la tracción 180 ksi (1241 MPa)
¿Buscas datos completos de desempeño de materiales?
Se requiere registro gratuito • Acceso inmediato
SAE Ti-10V-2Fe-3Al Propiedades físicas
Temperatura
Este material cuenta con 4475 propiedades — aquí solo se muestra una parte.
Consulta propiedades físicas detalladas en distintas temperaturas y condiciones.
Se requiere registro gratuito • Acceso inmediato
SAE Ti-10V-2Fe-3Al Tratamiento Térmico
- Solution Heat Treatment
Forgings shall be heated to a temperature 60 to 100°F (33 to 56°C) below the beta transus, held at heat for not less than 30 minutes, and quenched in water, unless a double solution heat treatment is specified by purchaser. In that case forgings shall be also heated to a temperature 60 to 100°F (33 to 56°C) below the beta transus, held at heat for not less than 30 minutes, and either furnace cooled or air cooled to room temperature.
Aging heat treatment: heat to a temperature within the range 900 to 975°F (482 to 524°C), hold at the selected temperature within ±10 °F (±6°C) for not less than 8 hours, and cool to room temperature.
Beta Transus Determination:
The beta transus temperature shall be determined by metallography, differential thermal analyzer, calculated from chemical composition of the alloy, or any method acceptable to purchaser. Thermal controls and readouts shall be calibrated to an accuracy of ±5°F (±3°C). - Solution Heat Treatment
Forgings shall be single solution heat treated by heating to a temperature 60 to 100°F (33 to 55°C) degrees below the beta transus, holding at heat for not less than 30 minutes, and cooling at a rate equivalent to an air cool or faster.
Beta Transus Determination
The beta transus temperature shall be determined by metallography, differential thermal analyzer, calculated from the chemical composition of the alloy, or a method acceptable to purchaser Thermal controls and readouts shall be calibrated to an accuracy of ±5°F (±3°C).
Aging
Heat to a temperature not lower than 900°F (482°C), hold at the selected temperature within ±10°F (±6°C) for not less than 8 hours, and cool to room temperature.
SAE Ti-10V-2Fe-3Al Propiedades mecánicas
Temperatura
¿Buscas información completa sobre propiedades mecánicas para tomar la mejor decisión?
Obtén información completa sobre resistencia, dureza, fatiga y más.
Se requiere registro gratuito • Acceso inmediato
SAE Ti-10V-2Fe-3Al Materiales Internacionales Equivalentes
Mostrando 8 de 32 resultados.
Las categorías de equivalencia reflejan comparaciones de composición química y propiedades mecánicas; siempre verifique la idoneidad del material según la especificación aplicable a su aplicación.
¿Necesita la lista completa de los 32 internacionales equivalentes?
Consulte los grados 32 equivalentes con el detalle completo de correspondencias por norma, fabricante y categoría de equivalencia.
Se requiere registro gratuito • Acceso inmediato
Optimiza la selección de materiales para tu aplicación - Reservar una demo
- 32Referencias cruzadas
- 44Composición
- 51Propiedades mecánicas
- 10Propiedades físicas
- 6Tratamiento térmico
- -Metalografía
- -Maquinabilidad
- 26Esfuerzo-Deformación
- -Conformabilidad
- 7Fatiga
- 4Fractura
- -Bicho raro
- -Uniones
- -Revestimientos
- -Dimensiones
- -Tribología
- 4283Corrosión
- -Envejecimiento
- -Resistencia a la intemperie
- -Irradiación
- 12Proveedores Totales