PROPRIETARY VP20ISO Aços de ferramenta
Atualizações de dados
Este material conta com 155 propriedades — apenas uma parte está sendo exibida aqui.
Desbloqueie todas as propriedades do material, incluindo valores detalhados em diferentes temperaturas e condições.
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY VP20ISO Composição química
Villares Metals, Product Data Sheets,
Precisa de dados completos de desempenho de materiais?
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY VP20ISO Propriedades físicas
Temperatura
Este material conta com 155 propriedades — apenas uma parte está sendo exibida aqui.
Desbloquear valores físicos específicos em diferentes temperaturas e condições.
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY VP20ISO Tratamento Térmico
- Annealing: Heating slowly to temperature between 760/800°C (100°C/h) for 1 hour, followed by slow cooling at 30°C per hour until 600°C and, then, by air cooling. In this treatment, the use of protective atmosphere is important to avoid surface oxidation and decarburization.
Stress relieving:The indicated procedure is slow heating (100°C/h) up to 530°C, keeping 0.5 hour in temperature for each 25 mm of the largest section in the part; regardless of the section, the time must not be less than 2 hours. After relief, cool in calm air.
Quenching and Tempering: Heat slowly and uniformly at (100°C/h) up to 400°C and then at a maximum of 300°C/h until the austenitization temperature, between 840 and 860°C. Keep at temperature until complete homogenization of the entire piece. Cooling must be carried out in oil suitable for quenching, stirred and heated between 40 and 70°C, until the mold temperature reaches 100°C. Then cool in calm air between 50 and 70°C. The tools must be tempered immediately after hardening, as soon as they reach 60°C. Make at least 2 tempers and between each temper the parts must cool slowly to room temperature. The tempering temperature must be chosen according to the desired hardness. The time of each tempering must be at least 2 hours. For pieces larger than 70 mm, the time must be calculated as a function of their dimension. Allow 1 hour for each inch of thickness.
Nitriding: It must be carried out after quenching and tempering, as long as the nitriding temperature is at least 50°C lower than the temperature of the last tempering.
PROPRIETARY VP20ISO Propriedades mecânicas
Temperatura
Precisa de propriedades mecânicas completas para fazer a escolha certa?
Acesse dados detalhados de resistência, dureza, fadiga e muito mais.
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY VP20ISO Materiais Equivalentes Internacionais
Exibindo 15 de 71 resultados.
As categorias de equivalência refletem a comparação da composição química e das propriedades mecânicas, sempre verifique a adequação do material em relação à especificação aplicável à sua aplicação.
Precisa da lista completa do 71 de equivalentes internacionais?
Veja todos as classes 71 equivalentes com mapeamento detalhado por norma, fabricante e categoria de equivalência.
Registro gratuito requerido • Acesso instantâneo
Otimizar seleção de materiais para sua aplicação - Agende uma demonstração
- 71Referências Cruzadas
- 5Composição
- 1Propriedades Mecânicas
- 7Propriedades físicas
- 4Tratamento térmico
- -Metalografia
- -Usinabilidade
- -Tensão-Deformação
- -Conformabilidade
- -Fadiga
- -Fratura
- -Rastejante
- -Junta
- -Revestimentos
- -Dimensões
- -Tribologia
- -Corrosão
- -Envelhecimento
- -Resistência às Intempéries
- -Irradiação
- 67Total de Fornecedores