PROPRIETARY VP20ISO Acciai per utensili
Aggiornamenti dei dati
Questo materiale dispone di 155 dati sulle proprietà — qui ne viene mostrato solo un sottoinsieme.
Sblocca tutte le proprietà del materiale, inclusi i valori dettagliati a diverse temperature e condizioni.
Registrazione gratuita richiesta • Accesso immediato
PROPRIETARY VP20ISO Composizione chimica
Villares Metals, Product Data Sheets,
Cerchi dati completi sulle prestazioni dei materiali?
Registrazione gratuita richiesta • Accesso immediato
PROPRIETARY VP20ISO Proprietà fisiche
Temperatura
Questo materiale dispone di 155 dati sulle proprietà — qui ne viene mostrato solo un sottoinsieme.
Sblocca valori fisici dettagliati a diverse temperature e condizioni.
Registrazione gratuita richiesta • Accesso immediato
PROPRIETARY VP20ISO Trattamento Termico
- Annealing: Heating slowly to temperature between 760/800°C (100°C/h) for 1 hour, followed by slow cooling at 30°C per hour until 600°C and, then, by air cooling. In this treatment, the use of protective atmosphere is important to avoid surface oxidation and decarburization.
Stress relieving:The indicated procedure is slow heating (100°C/h) up to 530°C, keeping 0.5 hour in temperature for each 25 mm of the largest section in the part; regardless of the section, the time must not be less than 2 hours. After relief, cool in calm air.
Quenching and Tempering: Heat slowly and uniformly at (100°C/h) up to 400°C and then at a maximum of 300°C/h until the austenitization temperature, between 840 and 860°C. Keep at temperature until complete homogenization of the entire piece. Cooling must be carried out in oil suitable for quenching, stirred and heated between 40 and 70°C, until the mold temperature reaches 100°C. Then cool in calm air between 50 and 70°C. The tools must be tempered immediately after hardening, as soon as they reach 60°C. Make at least 2 tempers and between each temper the parts must cool slowly to room temperature. The tempering temperature must be chosen according to the desired hardness. The time of each tempering must be at least 2 hours. For pieces larger than 70 mm, the time must be calculated as a function of their dimension. Allow 1 hour for each inch of thickness.
Nitriding: It must be carried out after quenching and tempering, as long as the nitriding temperature is at least 50°C lower than the temperature of the last tempering.
PROPRIETARY VP20ISO Proprietà meccaniche
Temperatura
Hai bisogno di proprietà meccaniche complete per fare la scelta giusta?
Accedi ai dati completi su resistenza, durezza, fatica e altro ancora.
Registrazione gratuita richiesta • Accesso immediato
Materiali equivalenti internazionali di PROPRIETARY VP20ISO
Visualizzazione di 15 risultati su 71.
Le categorie di equivalenza si basano sul confronto della composizione chimica e delle proprietà meccaniche. Si raccomanda di verificare sempre l'idoneità del materiale rispetto alla specifica e all'applicazione prevista.
Hai bisogno dell'elenco completo dei 71 equivalenti internazionali?
Visualizza tutti i 71 gradi equivalenti con una mappatura dettagliata per norma, produttore e categoria di equivalenza.
Registrazione gratuita richiesta • Accesso immediato
Ottimizza la selezione dei materiali per la tua applicazione - Prenota una demo
- 71Riferimenti incrociati
- 5Composizione
- 1Proprietà meccaniche
- 7Proprietà fisiche
- 4Trattamento Termico
- -Metallografia
- -Lavorabilità
- -Sforzo-Deformazione
- -Formabilità
- -Fatica
- -Frattura
- -Strisciare
- -Giunzioni
- -Rivestimenti
- -Dimensioni
- -Tribologia
- -Corrosione
- -Invecchiamento
- -Resistenza agli agenti atmosferici
- -Irraggiamento
- 67Fornitori Totali