PROPRIETARY VP20ISO Aceros para herramientas
Actualizaciones de datos
Este material cuenta con 155 propiedades — aquí solo se muestra una parte.
Accede a todas las propiedades del material, incluyendo valores detallados según temperatura y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY VP20ISO Composición química
Villares Metals, Product Data Sheets,
¿Buscas datos completos de desempeño de materiales?
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY VP20ISO Propiedades físicas
Temperatura
Este material cuenta con 155 propiedades — aquí solo se muestra una parte.
Consulta propiedades físicas detalladas en distintas temperaturas y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY VP20ISO Tratamiento Térmico
- Annealing: Heating slowly to temperature between 760/800°C (100°C/h) for 1 hour, followed by slow cooling at 30°C per hour until 600°C and, then, by air cooling. In this treatment, the use of protective atmosphere is important to avoid surface oxidation and decarburization.
Stress relieving:The indicated procedure is slow heating (100°C/h) up to 530°C, keeping 0.5 hour in temperature for each 25 mm of the largest section in the part; regardless of the section, the time must not be less than 2 hours. After relief, cool in calm air.
Quenching and Tempering: Heat slowly and uniformly at (100°C/h) up to 400°C and then at a maximum of 300°C/h until the austenitization temperature, between 840 and 860°C. Keep at temperature until complete homogenization of the entire piece. Cooling must be carried out in oil suitable for quenching, stirred and heated between 40 and 70°C, until the mold temperature reaches 100°C. Then cool in calm air between 50 and 70°C. The tools must be tempered immediately after hardening, as soon as they reach 60°C. Make at least 2 tempers and between each temper the parts must cool slowly to room temperature. The tempering temperature must be chosen according to the desired hardness. The time of each tempering must be at least 2 hours. For pieces larger than 70 mm, the time must be calculated as a function of their dimension. Allow 1 hour for each inch of thickness.
Nitriding: It must be carried out after quenching and tempering, as long as the nitriding temperature is at least 50°C lower than the temperature of the last tempering.
PROPRIETARY VP20ISO Propiedades mecánicas
Temperatura
¿Buscas información completa sobre propiedades mecánicas para tomar la mejor decisión?
Obtén información completa sobre resistencia, dureza, fatiga y más.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY VP20ISO Materiales Internacionales Equivalentes
Mostrando 15 de 71 resultados.
Las categorías de equivalencia reflejan comparaciones de composición química y propiedades mecánicas; siempre verifique la idoneidad del material según la especificación aplicable a su aplicación.
¿Necesita la lista completa de los 71 internacionales equivalentes?
Consulte los grados 71 equivalentes con el detalle completo de correspondencias por norma, fabricante y categoría de equivalencia.
Se requiere registro gratuito • Acceso inmediato
Optimiza la selección de materiales para tu aplicación - Reservar una demo
- 71Referencias cruzadas
- 5Composición
- 1Propiedades mecánicas
- 7Propiedades físicas
- 4Tratamiento térmico
- -Metalografía
- -Maquinabilidad
- -Esfuerzo-Deformación
- -Conformabilidad
- -Fatiga
- -Fractura
- -Bicho raro
- -Uniones
- -Revestimientos
- -Dimensiones
- -Tribología
- -Corrosión
- -Envejecimiento
- -Resistencia a la intemperie
- -Irradiación
- 67Proveedores Totales