PROPRIETARY CPM 10V Aços de ferramenta
Atualizações de dados
Este material conta com 42 propriedades — apenas uma parte está sendo exibida aqui.
Desbloqueie todas as propriedades do material, incluindo valores detalhados em diferentes temperaturas e condições.
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY CPM 10V Composição química
ZAPP AG, Product Data Sheets,
Precisa de dados completos de desempenho de materiais?
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY CPM 10V Propriedades físicas
Temperatura
Este material conta com 42 propriedades — apenas uma parte está sendo exibida aqui.
Desbloquear valores físicos específicos em diferentes temperaturas e condições.
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY CPM 10V Tratamento Térmico
- SOFT ANNEALING The material is heated uniformly to a temperature of 850 - 900 °C; maintain temperature for 2 hours and allow to cool to 540 °C in the furnace at a cooling rate of 10 °C per hour. This is followed by cooling in air. The typical hardness achieved by soft annealing is HB 250 – 270. STRES S RELIEVING follows rough machining by heating to a temperature of 600 – 700 °C. Once complete heat penetration has been reached, the material is allowed to cool in the furnace to approx. 500 °C followed by cooling in air. HARDENING usually involves the use of 2 preheating stages (450 – 500 °C/ 850 – 900 °C). The material is then rapidly heated from the preheating temperature to the austenitizing temperature of 1070 °C to 1180 °C; 1070 °C for achieving optimum toughness and 1180 °C for achieving maximum wear resistance. To achieve a corresponding degree of dissolution of the alloy elements as well as an appropriate hardening and tempering level, a minimum heat penetration time of 30 min. is recommended for hardening at 1070 °C and a minimum heat penetration time of 10 min. for hardening at 1180 °C. These temperature equalisation times should be correspondingly adapted for large or very thick-walled material cross-sections. QUENCHING Air, hot bath or interrupted oil quenching can be used. We recommend hot bath quenching at approx. 550 °C. Particular care must be taken in case of protective gas or vacuum heat treatment to ensure that an appropriate quenching rate is achieved in order to obtain the required hardness level at the recommended tempering temperature. TEMPERING immediately after the tools have been quenched to a temperature below 40 °C. Two-stage tempering is obligatory while triple tempering is recommended particularly when hardening takes place at temperatures above 1150 °C. It is important to ensure the tools are quenched to room temperature between the individual tempering processes. The standard tempering temperature is 540 °C. With exception to the stress relieving procedure, temperatures below 540 °C should be avoided in order to ensure effective tempering treatment. SURFACE TREATMENTS can be nitrided or PVD/ CVD coated.
PROPRIETARY CPM 10V Propriedades mecânicas
Temperatura
Precisa de propriedades mecânicas completas para fazer a escolha certa?
Acesse dados detalhados de resistência, dureza, fadiga e muito mais.
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY CPM 10V Materiais Equivalentes Internacionais
Exibindo 2 de 10 resultados.
As categorias de equivalência refletem a comparação da composição química e das propriedades mecânicas, sempre verifique a adequação do material em relação à especificação aplicável à sua aplicação.
Precisa da lista completa do 10 de equivalentes internacionais?
Veja todos as classes 10 equivalentes com mapeamento detalhado por norma, fabricante e categoria de equivalência.
Registro gratuito requerido • Acesso instantâneo
Otimizar seleção de materiais para sua aplicação - Agende uma demonstração
- 10Referências Cruzadas
- 10Composição
- 9Propriedades Mecânicas
- 7Propriedades físicas
- 1Tratamento térmico
- 2Metalografia
- -Usinabilidade
- -Tensão-Deformação
- -Conformabilidade
- -Fadiga
- -Fratura
- -Rastejante
- -Junta
- -Revestimentos
- -Dimensões
- -Tribologia
- -Corrosão
- -Envelhecimento
- -Resistência às Intempéries
- -Irradiação
- 3Total de Fornecedores