PROPRIETARY CPM 10V Acciai per utensili
Aggiornamenti dei dati
Questo materiale dispone di 42 dati sulle proprietà — qui ne viene mostrato solo un sottoinsieme.
Sblocca tutte le proprietà del materiale, inclusi i valori dettagliati a diverse temperature e condizioni.
Registrazione gratuita richiesta • Accesso immediato
PROPRIETARY CPM 10V Composizione chimica
ZAPP AG, Product Data Sheets,
Cerchi dati completi sulle prestazioni dei materiali?
Registrazione gratuita richiesta • Accesso immediato
PROPRIETARY CPM 10V Proprietà fisiche
Temperatura
Questo materiale dispone di 42 dati sulle proprietà — qui ne viene mostrato solo un sottoinsieme.
Sblocca valori fisici dettagliati a diverse temperature e condizioni.
Registrazione gratuita richiesta • Accesso immediato
PROPRIETARY CPM 10V Trattamento Termico
- SOFT ANNEALING The material is heated uniformly to a temperature of 850 - 900 °C; maintain temperature for 2 hours and allow to cool to 540 °C in the furnace at a cooling rate of 10 °C per hour. This is followed by cooling in air. The typical hardness achieved by soft annealing is HB 250 – 270. STRES S RELIEVING follows rough machining by heating to a temperature of 600 – 700 °C. Once complete heat penetration has been reached, the material is allowed to cool in the furnace to approx. 500 °C followed by cooling in air. HARDENING usually involves the use of 2 preheating stages (450 – 500 °C/ 850 – 900 °C). The material is then rapidly heated from the preheating temperature to the austenitizing temperature of 1070 °C to 1180 °C; 1070 °C for achieving optimum toughness and 1180 °C for achieving maximum wear resistance. To achieve a corresponding degree of dissolution of the alloy elements as well as an appropriate hardening and tempering level, a minimum heat penetration time of 30 min. is recommended for hardening at 1070 °C and a minimum heat penetration time of 10 min. for hardening at 1180 °C. These temperature equalisation times should be correspondingly adapted for large or very thick-walled material cross-sections. QUENCHING Air, hot bath or interrupted oil quenching can be used. We recommend hot bath quenching at approx. 550 °C. Particular care must be taken in case of protective gas or vacuum heat treatment to ensure that an appropriate quenching rate is achieved in order to obtain the required hardness level at the recommended tempering temperature. TEMPERING immediately after the tools have been quenched to a temperature below 40 °C. Two-stage tempering is obligatory while triple tempering is recommended particularly when hardening takes place at temperatures above 1150 °C. It is important to ensure the tools are quenched to room temperature between the individual tempering processes. The standard tempering temperature is 540 °C. With exception to the stress relieving procedure, temperatures below 540 °C should be avoided in order to ensure effective tempering treatment. SURFACE TREATMENTS can be nitrided or PVD/ CVD coated.
PROPRIETARY CPM 10V Proprietà meccaniche
Temperatura
Hai bisogno di proprietà meccaniche complete per fare la scelta giusta?
Accedi ai dati completi su resistenza, durezza, fatica e altro ancora.
Registrazione gratuita richiesta • Accesso immediato
Materiali equivalenti internazionali di PROPRIETARY CPM 10V
Visualizzazione di 2 risultati su 10.
Le categorie di equivalenza si basano sul confronto della composizione chimica e delle proprietà meccaniche. Si raccomanda di verificare sempre l'idoneità del materiale rispetto alla specifica e all'applicazione prevista.
Hai bisogno dell'elenco completo dei 10 equivalenti internazionali?
Visualizza tutti i 10 gradi equivalenti con una mappatura dettagliata per norma, produttore e categoria di equivalenza.
Registrazione gratuita richiesta • Accesso immediato
Ottimizza la selezione dei materiali per la tua applicazione - Prenota una demo
- 10Riferimenti incrociati
- 10Composizione
- 9Proprietà meccaniche
- 7Proprietà fisiche
- 1Trattamento Termico
- 2Metallografia
- -Lavorabilità
- -Sforzo-Deformazione
- -Formabilità
- -Fatica
- -Frattura
- -Strisciare
- -Giunzioni
- -Rivestimenti
- -Dimensioni
- -Tribologia
- -Corrosione
- -Invecchiamento
- -Resistenza agli agenti atmosferici
- -Irraggiamento
- 3Fornitori Totali