PROPRIETARY CPM 10V Aceros para herramientas
Actualizaciones de datos
Este material cuenta con 42 propiedades — aquí solo se muestra una parte.
Accede a todas las propiedades del material, incluyendo valores detallados según temperatura y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY CPM 10V Composición química
ZAPP AG, Product Data Sheets,
¿Buscas datos completos de desempeño de materiales?
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY CPM 10V Propiedades físicas
Temperatura
Este material cuenta con 42 propiedades — aquí solo se muestra una parte.
Consulta propiedades físicas detalladas en distintas temperaturas y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY CPM 10V Tratamiento Térmico
- SOFT ANNEALING The material is heated uniformly to a temperature of 850 - 900 °C; maintain temperature for 2 hours and allow to cool to 540 °C in the furnace at a cooling rate of 10 °C per hour. This is followed by cooling in air. The typical hardness achieved by soft annealing is HB 250 – 270. STRES S RELIEVING follows rough machining by heating to a temperature of 600 – 700 °C. Once complete heat penetration has been reached, the material is allowed to cool in the furnace to approx. 500 °C followed by cooling in air. HARDENING usually involves the use of 2 preheating stages (450 – 500 °C/ 850 – 900 °C). The material is then rapidly heated from the preheating temperature to the austenitizing temperature of 1070 °C to 1180 °C; 1070 °C for achieving optimum toughness and 1180 °C for achieving maximum wear resistance. To achieve a corresponding degree of dissolution of the alloy elements as well as an appropriate hardening and tempering level, a minimum heat penetration time of 30 min. is recommended for hardening at 1070 °C and a minimum heat penetration time of 10 min. for hardening at 1180 °C. These temperature equalisation times should be correspondingly adapted for large or very thick-walled material cross-sections. QUENCHING Air, hot bath or interrupted oil quenching can be used. We recommend hot bath quenching at approx. 550 °C. Particular care must be taken in case of protective gas or vacuum heat treatment to ensure that an appropriate quenching rate is achieved in order to obtain the required hardness level at the recommended tempering temperature. TEMPERING immediately after the tools have been quenched to a temperature below 40 °C. Two-stage tempering is obligatory while triple tempering is recommended particularly when hardening takes place at temperatures above 1150 °C. It is important to ensure the tools are quenched to room temperature between the individual tempering processes. The standard tempering temperature is 540 °C. With exception to the stress relieving procedure, temperatures below 540 °C should be avoided in order to ensure effective tempering treatment. SURFACE TREATMENTS can be nitrided or PVD/ CVD coated.
PROPRIETARY CPM 10V Propiedades mecánicas
Temperatura
¿Buscas información completa sobre propiedades mecánicas para tomar la mejor decisión?
Obtén información completa sobre resistencia, dureza, fatiga y más.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY CPM 10V Materiales Internacionales Equivalentes
Mostrando 2 de 10 resultados.
Las categorías de equivalencia reflejan comparaciones de composición química y propiedades mecánicas; siempre verifique la idoneidad del material según la especificación aplicable a su aplicación.
¿Necesita la lista completa de los 10 internacionales equivalentes?
Consulte los grados 10 equivalentes con el detalle completo de correspondencias por norma, fabricante y categoría de equivalencia.
Se requiere registro gratuito • Acceso inmediato
Optimiza la selección de materiales para tu aplicación - Reservar una demo
- 10Referencias cruzadas
- 10Composición
- 9Propiedades mecánicas
- 7Propiedades físicas
- 1Tratamiento térmico
- 2Metalografía
- -Maquinabilidad
- -Esfuerzo-Deformación
- -Conformabilidad
- -Fatiga
- -Fractura
- -Bicho raro
- -Uniones
- -Revestimientos
- -Dimensiones
- -Tribología
- -Corrosión
- -Envejecimiento
- -Resistencia a la intemperie
- -Irradiación
- 3Proveedores Totales