PROPRIETARY VTMPLUS Acciai per utensili
Aggiornamenti dei dati
Questo materiale dispone di 73 dati sulle proprietà — qui ne viene mostrato solo un sottoinsieme.
Sblocca tutte le proprietà del materiale, inclusi i valori dettagliati a diverse temperature e condizioni.
Registrazione gratuita richiesta • Accesso immediato
PROPRIETARY VTMPLUS Proprietà fisiche
Temperatura
Questo materiale dispone di 73 dati sulle proprietà — qui ne viene mostrato solo un sottoinsieme.
Sblocca valori fisici dettagliati a diverse temperature e condizioni.
Registrazione gratuita richiesta • Accesso immediato
PROPRIETARY VTMPLUS Trattamento Termico
- Recommendations to Improve Tool Life: Preheat dies and components slowly between (200 - 300°C) to obtain thermal uniformity of core and surface. Apply a regular maintenance of stress tempering throughout the operation of the tool to reduce stresses.
Heat Treatment Procedures: Soft annealing should be carried out by heating between 840 and 860°C for 2 hours, followed by slow cooling at 10/20°C per hour until 650°C and, then, by air cooling. In this treatment, the use of protective atmosphere is important to avoid surface oxidation and decarburization.
Stress Relief: To be implemented after rough machining. Slowly heat the tool to 650°C, holding time 2 hours. Furnace cool to 200°C and then freely in air.
Hardening: Preheating: 600 - 850°C, normally in two steps. Equalize surface to center at each step.
Austenitizing temperature: 1030 - 1050°C. This is the recommended range for all tooling obtain the best material toughness.
Quenching media:
a) Pressurized vacuum furnace, preferably with at least 5 bar overpressure capability;
b) Warm oil, 40 - 70°C;
c) Salt or fluidized bed between 450 - 550°C.
Tempering: Tools must be tempered immediately after hardening, as soon as they reach 50 - 70°C. Temper at least twice. Cool to room temperature between tempers. Holding time at temperature is a minimum 2 hours.
Nitriding: It must be employed after hardening and tempering, since the temperature is at least 30°C lower than the last tempering temperature.
Tempering Resistance: It shows higher resistance to softening at elevated temperatures than typical hot work tools steels.
PROPRIETARY VTMPLUS Proprietà meccaniche
Temperatura
Hai bisogno di proprietà meccaniche complete per fare la scelta giusta?
Accedi ai dati completi su resistenza, durezza, fatica e altro ancora.
Registrazione gratuita richiesta • Accesso immediato
Materiali equivalenti internazionali di PROPRIETARY VTMPLUS
Visualizzazione di 12 risultati su 52.
Le categorie di equivalenza si basano sul confronto della composizione chimica e delle proprietà meccaniche. Si raccomanda di verificare sempre l'idoneità del materiale rispetto alla specifica e all'applicazione prevista.
Hai bisogno dell'elenco completo dei 52 equivalenti internazionali?
Visualizza tutti i 52 gradi equivalenti con una mappatura dettagliata per norma, produttore e categoria di equivalenza.
Registrazione gratuita richiesta • Accesso immediato
Ottimizza la selezione dei materiali per la tua applicazione - Prenota una demo
- 52Riferimenti incrociati
- -Composizione
- 1Proprietà meccaniche
- 4Proprietà fisiche
- 2Trattamento Termico
- -Metallografia
- -Lavorabilità
- -Sforzo-Deformazione
- -Formabilità
- -Fatica
- -Frattura
- -Strisciare
- -Giunzioni
- -Rivestimenti
- -Dimensioni
- -Tribologia
- -Corrosione
- -Invecchiamento
- -Resistenza agli agenti atmosferici
- -Irraggiamento
- 14Fornitori Totali