PROPRIETARY VTMPLUS Acier pour outils
Mises à jour des données
Ce matériau a 73 entrées de propriétés – seul un aperçu est visible ici.
Déverrouillez l’accès aux propriétés détaillées du matériau, notamment en température et dans différentes conditions.
Inscription gratuite requise • Accès instantané
PROPRIETARY VTMPLUS Propriétés physiques
Température
Ce matériau a 73 entrées de propriétés – seul un aperçu est visible ici.
Déverrouiller l’accès aux propriétés physiques à différentes températures et conditions.
Inscription gratuite requise • Accès instantané
PROPRIETARY VTMPLUS Traitement thermique
- Recommendations to Improve Tool Life: Preheat dies and components slowly between (200 - 300°C) to obtain thermal uniformity of core and surface. Apply a regular maintenance of stress tempering throughout the operation of the tool to reduce stresses.
Heat Treatment Procedures: Soft annealing should be carried out by heating between 840 and 860°C for 2 hours, followed by slow cooling at 10/20°C per hour until 650°C and, then, by air cooling. In this treatment, the use of protective atmosphere is important to avoid surface oxidation and decarburization.
Stress Relief: To be implemented after rough machining. Slowly heat the tool to 650°C, holding time 2 hours. Furnace cool to 200°C and then freely in air.
Hardening: Preheating: 600 - 850°C, normally in two steps. Equalize surface to center at each step.
Austenitizing temperature: 1030 - 1050°C. This is the recommended range for all tooling obtain the best material toughness.
Quenching media:
a) Pressurized vacuum furnace, preferably with at least 5 bar overpressure capability;
b) Warm oil, 40 - 70°C;
c) Salt or fluidized bed between 450 - 550°C.
Tempering: Tools must be tempered immediately after hardening, as soon as they reach 50 - 70°C. Temper at least twice. Cool to room temperature between tempers. Holding time at temperature is a minimum 2 hours.
Nitriding: It must be employed after hardening and tempering, since the temperature is at least 30°C lower than the last tempering temperature.
Tempering Resistance: It shows higher resistance to softening at elevated temperatures than typical hot work tools steels.
PROPRIETARY VTMPLUS Propriétés mécaniques
Température
Vous avez besoin des propriétés mécaniques détaillées pour faire le bon choix ?
Accédez aux données complètes de résistance, dureté, fatigue et plus encore.
Inscription gratuite requise • Accès instantané
PROPRIETARY VTMPLUS Matériaux équivalents internationaux
Affichage de 12 sur 52 résultats.
Les catégories d'équivalence reflètent une comparaison de la composition chimique et des propriétés mécaniques — vérifiez toujours l'adéquation par rapport à la spécification applicable à votre utilisation.
Besoin de la liste complète des 52 équivalents internationaux ?
Consultez les 52 nuances équivalentes avec une correspondance détaillée par norme, producteur et catégorie d'équivalence.
Inscription gratuite requise • Accès instantané
Optimisez les choix de matériaux pour votre application - Réserver une démo
- 52Références croisées
- -Composition
- 1Propriétés mécaniques
- 4Propriétés physiques
- 2Traitement thermique
- -Métallographie
- -Usinabilité
- -Contrainte-Déformation
- -Formabilité
- -Fatigue
- -Rupture
- -Rampant
- -Assemblages
- -Revêtements
- -Dimensions
- -Tribologie
- -Corrosion
- -Vieillissement
- -Résistance aux intempéries
- -Irradiation
- 14Fournisseurs totaux