PROPRIETARY Uddeholm Vanadis 23 SuperClean Acier pour outils
Mises à jour des données
Ce matériau a 153 entrées de propriétés – seul un aperçu est visible ici.
Déverrouillez l’accès aux propriétés détaillées du matériau, notamment en température et dans différentes conditions.
Inscription gratuite requise • Accès instantané
PROPRIETARY Uddeholm Vanadis 23 SuperClean Composition chimique
Uddeholms AB, Product Data Sheets,
Vous souhaitez voir toutes les données sur ce matériau ?
Inscription gratuite requise • Accès instantané
PROPRIETARY Uddeholm Vanadis 23 SuperClean Propriétés physiques
Température
Ce matériau a 153 entrées de propriétés – seul un aperçu est visible ici.
Déverrouiller l’accès aux propriétés physiques à différentes températures et conditions.
Inscription gratuite requise • Accès instantané
PROPRIETARY Uddeholm Vanadis 23 SuperClean Traitement thermique
- Soft annealing:
Protect the steel and heat through to 850-900°C (1560-1650°F). Then cool in the furnace at 10°C/h (20°F/h) to 700°C (1290°F), then freely in air;
Stress relieving:
After rough machining the tool should be heated through to 600-700°C (1110-1290°F), holding time 2 hr. Cool slowly to 500°C (930°F), then freely in air;
Hardening:
Preheating temperature: 450-500°C (840-930°F) and 850-900°C (1560-1650°F). Austenitizing temperature: 1050-1180°C (1920-2160°F) according to the desired final hardness;
Quenching media: Vacuum furnace with high speed gas at sufficient overpressure (2-5 bar), Martempering bath or fluidized bed at approx. 550°C (1020°F), Forced air/gas (Quenching should be continued until the temperature of the tool reaches approx. 50°C (120°F). The tool should then be tempered immediately; For applications where maximum toughness is required use a martempering bath or a furnace with sufficient overpressure.)
Tempering:
For cold work applications tempering should always be carried out at 560°C (1040°F) irrespective of the austenitizing temperature. Temper three times for one hour at full temperature. The tool should be cooled to room temperature between the tempers. The retained austenite content will be less than 1% after this tempering cycle.
Sub-zero treatment: For materials that require maximum dimensional stability, immediately after quenching the piece should be sub-zero treated -70 to -80°C (-95 to -110°F), soaking for 1-3 h and followed by tempering. - Austenitizing temperature 1080°C (1980°F). Holding time 30 minutes.
PROPRIETARY Uddeholm Vanadis 23 SuperClean Propriétés mécaniques
Température
Vous avez besoin des propriétés mécaniques détaillées pour faire le bon choix ?
Accédez aux données complètes de résistance, dureté, fatigue et plus encore.
Inscription gratuite requise • Accès instantané
PROPRIETARY Uddeholm Vanadis 23 SuperClean Matériaux équivalents internationaux
Affichage de 15 résultats sur 68.
Les catégories d'équivalence reflètent la comparaison de la composition chimique et des propriétés mécaniques — vérifiez toujours l'adéquation avec la spécification applicable à votre application.
Besoin de la liste complète des 68 équivalents internationaux ?
Consultez les 68 nuances équivalentes avec une cartographie détaillée par norme, producteur et catégorie d'équivalence.
Inscription gratuite requise • Accès instantané
Optimisez les choix de matériaux pour votre application - Réserver une démo
- 68Références croisées
- 5Composition
- 7Propriétés mécaniques
- 21Propriétés physiques
- 2Traitement thermique
- -Métallographie
- -Usinabilité
- -Contrainte-Déformation
- -Formabilité
- -Fatigue
- -Rupture
- -Rampant
- -Assemblages
- -Revêtements
- -Dimensions
- -Tribologie
- -Corrosion
- -Vieillissement
- -Résistance aux intempéries
- -Irradiation
- 50Fournisseurs totaux