PROPRIETARY CarTech No. 879 Aceros para herramientas
Actualizaciones de datos
Este material cuenta con 113 propiedades — aquí solo se muestra una parte.
Accede a todas las propiedades del material, incluyendo valores detallados según temperatura y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY CarTech No. 879 Composición química
Carpenter Technology Corporation, Product Data Sheets,
¿Buscas datos completos de desempeño de materiales?
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY CarTech No. 879 Propiedades físicas
Temperatura
Este material cuenta con 113 propiedades — aquí solo se muestra una parte.
Consulta propiedades físicas detalladas en distintas temperaturas y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY CarTech No. 879 Tratamiento Térmico
- Decarburization: Steel displays medium resistance to decarburization during thermal processing. Precautions must be taken to control this condition. Modern furnaces are available which provide environments designed to minimize decarburization.
Normalizing: Do not normalize.
Annealing: Anneal in a controlled atmosphere furnace or with a neutral packing compound. Heat slowly to 871-889°C (1600-1650°F), and hold until the entire mass is heated through. Cool slowly in the furnace 22°C (40°F) per hour to 593°C (1100°F), then air cool.
Hardening: Preheat slowly and uniformly to 816-843°C (1500-1550°F). Then heat more rapidly to an austenitizing temperature of 1093-1204°C (2000-2200°F). The lower end of the temperature range is only used when a relatively low final hardness is desired. Hold for 2-5 minutes at temperature and harden by cooling in air or oil. A controlled atmosphere or vacuum furnace should be used to minimize decarburization and oxidation.
Tempering: As soon as the hardened steel reaches 52-66°C (125-150°F), temper to the hardness desired as suggested in the chart on the following page. Double tempering is recommended to improve toughness and reduce heat cracking. Time at temperature should be no less than one and a half hours or one hour per inch of section.
Forging: Preforge heating must be slow and uniform. Soak through at 1038-1093°C (1900-2000°F) and reheat when necessary, stopping work when the temperature falls below 889°C (1650°F). After forging, cool slowly in furnace, mica, lime or dry ashes. Anneal as soon as possible after forging and cooling.
PROPRIETARY CarTech No. 879 Propiedades mecánicas
Temperatura
¿Buscas información completa sobre propiedades mecánicas para tomar la mejor decisión?
Obtén información completa sobre resistencia, dureza, fatiga y más.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY CarTech No. 879 Materiales equivalentes internacionales
Mostrando 6 de 7 resultados.
Las categorías de equivalencia reflejan la comparación de composición química y propiedades mecánicas — verifique siempre la idoneidad según la especificación aplicable a su aplicación.
¿Necesita la lista completa de 7 equivalentes internacionales?
Consulte los 7 grados equivalentes con mapeo detallado por norma, productor y categoría de equivalencia.
Se requiere registro gratuito • Acceso inmediato
Optimiza la selección de materiales para tu aplicación - Reservar una demo
- 7Referencias cruzadas
- 9Composición
- 85Propiedades mecánicas
- 9Propiedades físicas
- 1Tratamiento térmico
- -Metalografía
- -Maquinabilidad
- -Esfuerzo-Deformación
- -Conformabilidad
- -Fatiga
- -Fractura
- -Bicho raro
- -Uniones
- -Revestimientos
- -Dimensiones
- -Tribología
- -Corrosión
- -Envejecimiento
- -Resistencia a la intemperie
- -Irradiación
- 2Proveedores Totales