PROPRIETARY CarTech M42 High Speed Steel Aceros para herramientas
Actualizaciones de datos
Este material cuenta con 46 propiedades — aquí solo se muestra una parte.
Accede a todas las propiedades del material, incluyendo valores detallados según temperatura y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY CarTech M42 High Speed Steel Composición química
Carpenter Technology Corporation, Product Data Sheets,
¿Buscas datos completos de desempeño de materiales?
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY CarTech M42 High Speed Steel Propiedades físicas
Temperatura
Este material cuenta con 46 propiedades — aquí solo se muestra una parte.
Consulta propiedades físicas detalladas en distintas temperaturas y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY CarTech M42 High Speed Steel Tratamiento Térmico
- Decarburization: This steel, like all high speed steels, is subject to decarburization in hardening. The use of rectified salt baths or the proper atmosphere control in furnace hardening will impart good results in heat treating.
Normalizing: Normalizing is not recommended.
Annealing: To anneal, the steel should be packed in a container using a neutral packing compound or in a suitable protective atmosphere. Heat uniformly to 843-871°C (1550-1600°F) ensuring that the entire section is at temperature. Cool slowly in the furnace at a rate not to exceed 22°C (40°F) per hour to 538°C (1000°F), then allow to cool naturally. This should produce a hardness of BHN 255 or less.
Hardening: For best results this steel should be heat treated from properly rectified salt baths or controlled atmosphere furnaces. Preheat at 816-871°C (1500-1600°F) being sure to heat thoroughly, then transfer to the high heat of 1177-1204°C (2150-2200°F) in salt or 14°C (25°F) higher in atmosphere furnaces. Quench in salt at 538-621°C (1000-1150°F) until equalized, then cool in air. The steel may also be quenched in warm oil. In either case, cool to 66°C (150°F) maximum before tempering, but do not allow parts to be at room temperature for extended periods before placing in the tempering furnace.
Tempering: The alloy should normally be tempered between 510°C (950°F) and 593°C (1100°F). Tempering temperatures below 538°C (1000°F) usually do not provide adequate relief of hardening stresses and are not generally recommended. This steel should be given triple temper cycle with a minimum of two hours at temperature each time. The tools must be cooled completely to room temperature following each cycle so that the tempering may be completely effective.
PROPRIETARY CarTech M42 High Speed Steel Propiedades mecánicas
Temperatura
¿Buscas información completa sobre propiedades mecánicas para tomar la mejor decisión?
Obtén información completa sobre resistencia, dureza, fatiga y más.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY CarTech M42 High Speed Steel Materiales equivalentes internacionales
Mostrando 10 de 12 resultados.
Las categorías de equivalencia reflejan la comparación de composición química y propiedades mecánicas — verifique siempre la idoneidad según la especificación aplicable a su aplicación.
¿Necesita la lista completa de 12 equivalentes internacionales?
Consulte los 12 grados equivalentes con mapeo detallado por norma, productor y categoría de equivalencia.
Se requiere registro gratuito • Acceso inmediato
Optimiza la selección de materiales para tu aplicación - Reservar una demo
- 12Referencias cruzadas
- 9Composición
- 10Propiedades mecánicas
- 3Propiedades físicas
- 1Tratamiento térmico
- -Metalografía
- -Maquinabilidad
- -Esfuerzo-Deformación
- -Conformabilidad
- -Fatiga
- -Fractura
- -Bicho raro
- -Uniones
- -Revestimientos
- -Dimensiones
- -Tribología
- -Corrosión
- -Envejecimiento
- -Resistencia a la intemperie
- -Irradiación
- 11Proveedores Totales