PROPRIETARY CarTech M42 High Speed Steel Aços de ferramenta
Atualizações de dados
Este material conta com 46 propriedades — apenas uma parte está sendo exibida aqui.
Desbloqueie todas as propriedades do material, incluindo valores detalhados em diferentes temperaturas e condições.
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY CarTech M42 High Speed Steel Composição química
Carpenter Technology Corporation, Product Data Sheets,
Precisa de dados completos de desempenho de materiais?
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY CarTech M42 High Speed Steel Propriedades físicas
Temperatura
Este material conta com 46 propriedades — apenas uma parte está sendo exibida aqui.
Desbloquear valores físicos específicos em diferentes temperaturas e condições.
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY CarTech M42 High Speed Steel Tratamento Térmico
- Decarburization: This steel, like all high speed steels, is subject to decarburization in hardening. The use of rectified salt baths or the proper atmosphere control in furnace hardening will impart good results in heat treating.
Normalizing: Normalizing is not recommended.
Annealing: To anneal, the steel should be packed in a container using a neutral packing compound or in a suitable protective atmosphere. Heat uniformly to 843-871°C (1550-1600°F) ensuring that the entire section is at temperature. Cool slowly in the furnace at a rate not to exceed 22°C (40°F) per hour to 538°C (1000°F), then allow to cool naturally. This should produce a hardness of BHN 255 or less.
Hardening: For best results this steel should be heat treated from properly rectified salt baths or controlled atmosphere furnaces. Preheat at 816-871°C (1500-1600°F) being sure to heat thoroughly, then transfer to the high heat of 1177-1204°C (2150-2200°F) in salt or 14°C (25°F) higher in atmosphere furnaces. Quench in salt at 538-621°C (1000-1150°F) until equalized, then cool in air. The steel may also be quenched in warm oil. In either case, cool to 66°C (150°F) maximum before tempering, but do not allow parts to be at room temperature for extended periods before placing in the tempering furnace.
Tempering: The alloy should normally be tempered between 510°C (950°F) and 593°C (1100°F). Tempering temperatures below 538°C (1000°F) usually do not provide adequate relief of hardening stresses and are not generally recommended. This steel should be given triple temper cycle with a minimum of two hours at temperature each time. The tools must be cooled completely to room temperature following each cycle so that the tempering may be completely effective.
PROPRIETARY CarTech M42 High Speed Steel Propriedades mecânicas
Temperatura
Precisa de propriedades mecânicas completas para fazer a escolha certa?
Acesse dados detalhados de resistência, dureza, fadiga e muito mais.
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY CarTech M42 High Speed Steel Materiais equivalentes internacionais
Mostrando 10 de 12 resultados.
As categorias de equivalência refletem a comparação da composição química e das propriedades mecânicas — verifique sempre a adequação de acordo com a especificação aplicável à sua aplicação.
Precisa da lista completa de 12 equivalentes internacionais?
Veja todas as 12 classes equivalentes com mapeamento detalhado por norma, produtor e categoria de equivalência.
Registro gratuito requerido • Acesso instantâneo
Otimizar seleção de materiais para sua aplicação - Agende uma demonstração
- 12Referências Cruzadas
- 9Composição
- 10Propriedades Mecânicas
- 3Propriedades físicas
- 1Tratamento térmico
- -Metalografia
- -Usinabilidade
- -Tensão-Deformação
- -Conformabilidade
- -Fadiga
- -Fratura
- -Rastejante
- -Junta
- -Revestimentos
- -Dimensões
- -Tribologia
- -Corrosão
- -Envelhecimento
- -Resistência às Intempéries
- -Irradiação
- 11Total de Fornecedores